Call us 24/7+86 15396212224
Welcome to the official website of Kong&Jiang Automation Equipment Co., Ltd!
email:abbdrive88@gmail.com

Advantest Q8344A Fiber Optic Spectrum Analyzer

Optical Measuring Instruments and Optical Device Test Systems

Optical Spectrum Analyzer for Coherent Measurements

■Coherence measurement

■High-speed measurements at 1.5 sec/scan

Wide wavelength range from 0.35 micron to 1.75 micron

■Wavelength measurement accuracy of 0.1 nm

The Q8344A is an optical spectrum analyzer with a wide wavelength range from 0.35 to 1.75 µm.

By using a Fourier spectroscopy system with a Michelson interferometer, it is possible to analyze coherence that cannot be obtained with a dispersive spectroscopy system using a monochromator.

It demonstrates the ability to evaluate laser diodes for optical and video disks.

The Optical Measurement Instruments and www.abb-drive.com Optical Devices Test System has a built-in He-Ne laser used as a reference wavelength with a wavelength accuracy of ± 0.1 nm (1.3 µm), which ensures long-term measurement stability even without wavelength calibration.

With a maximum wavelength resolution of 0.05 nm (0.85 µm), the Q8344A is suitable for measuring laser diodes with narrow mode intervals.

Measurement speeds of about 1.5 seconds (0.4 to 1.05 µm and 0.8 to 1.75 µm) are independent of the analysis span, so it can be used as a system component.

With its versatile display, analysis, and processing capabilities, the Q8344A can be used for a variety of component characterization applications, from light-emitting components such as laser diodes and LEDs to optical components such as optical fibers and filters.

Coherent Measurements

Since the Q8344A uses a Michelson interferometer, it can be used for coherence measurements. This feature makes it easy to evaluate the performance of noise suppression caused by the return light of laser diodes in video disks.

An analysis range of approximately ±10 mm enables measurement of the coherence length of SLDs (Super Light Emitting Diodes) used in fiber optic gyros.

High-speed measurement at 1.5 sec/scan

Ideal for production applications

The Q8344A utilizes a Fourier spectroscopy system so that measurements can be completed in less than 1.5 seconds, regardless of the measurement span and sensitivity (provided that the starting wavelength is 0.4 µm or longer and that the measurement does not cover both short and long wavelengths).

The analyzer is therefore suitable for measuring laser diodes and light emitting diodes on production lines. In addition, it can be used to evaluate the transmission and loss characteristics of optical fibers and filters.

When used as a system component, the analyzer can be triggered, measured, and output data in just 1.5 seconds, dramatically increasing system throughput.

Wavelength measurement accuracy of ± 0.1 nm

Measurements are accurate to ± 0.1 nm (1.3 µm) using the built-in He-Ne laser as a reference light source.

As a result, accurate wavelength measurements can be made without wavelength calibration.

Maximum wavelength range of 0.05 nm

The Q8344A has a maximum resolution of 0.05 nm at short wavelengths (0.85 µm), making it possible to measure CD and visible laser diodes in fully resolved oscillation mode, one by one.

Large-diameter fiber input (option)

An optional 200 µm large aperture input is available. This option is required when analyzing devices with wavelengths larger than the standard fiber aperture (GI 50 µm).

For laser diode analysis, the standard 50 µm size is recommended, while for LED analysis, this optional size is recommended.

Advantest Q8384 High-End Optical Spectrum Analyzer

The Q8384 Optical Spectrum Analyzer measures and evaluates ultra-high-speed optical DWDM transmission systems and optical components with high wavelength resolution and high accuracy.

The new high-end optical spectrum analyzer utilizes a new four-pass monochromator system to provide high wavelength resolution and wide dynamic range.

● 10 pm resolution bandwidth

● 20 pm wavelength accuracy (using Opt.)

● Wide dynamic range: 50 dB (±0.1 nm), 60 dB (±0.2 nm)

● Optical frequency display

● Accurate NF measurement of EDFAs

● Handles power levels up to +23 dBm (200 mW)

● Rich WDM analysis functions

● Provides limit line function for pass/fail analysis

In DWDM optical communications, accurate wavelength measurements of light sources are required. Evaluating these specifications requires optical spectrum analyzers with higher resolution bandwidth and wavelength accuracy.

To meet these stringent requirements, the Q8384 has the world’s highest wavelength resolution of 10 pm* and wavelength accuracy of 20 pm.

It also achieves 20 pm wavelength accuracy in the 1550 nm band. This high performance enables the Q8384 to accurately measure the oscillating wavelength characteristics of laser diodes.

DWDM optical communication systems also include wavelength division multiplexing channels.

DWDM optical communication systems also contain WDM channels spaced close to 50 GHz (0.4 nm).

In this environment, an optical spectrum analyzer with excellent dynamic range is required to separate the optical signal and measure the noise figure (NF) of the optical amplifier.

With a dynamic range of 50 dB at 0.1 nm and 60 dB at 0.2 nm, the Q8384 fully meets these requirements.

The instrument is equipped with an automatic optical amplifier NF measurement and calculation function, allowing the user to perform the measurement in a simple manner.

The Q8384 can be optionally equipped with a built-in reference wavelength light source and an EE-LED (Edge Light Emitting Diode).

When calibrated with this reference light source, the instrument ensures wavelength accuracy of 20 pm in the 1550 nm band.

Utilizing the EE-LED’s broadband light source, the Q8384 allows the user to easily measure and evaluate the transmission and loss characteristics of narrowband filters.

Superior Fundamental Performance

10 pm High Wavelength Resolution The Q8384 achieves a wavelength resolution bandwidth of up to 10 pm by using a newly developed monochromator system.

This makes it possible to measure and evaluate the sidebands of 10 Gbps intensity-modulated optical signals, a task previously impossible with conventional spectrum analyzers.

20 pm high wavelength accuracy

Calibrated with the built-in calibration light source (option 25), the Q8384 achieves wavelength measurement accuracy of ±20 pm in the C-band wavelength range from 1530 to 1570 nm.

The Q8384 achieves wavelength measurement accuracy of ±20 pm in the C-band wavelength range of 1530 to 1570 nm and ±40 pm in the L-band wavelength range of 1570 to 1610 nm.

It enables accurate characterization of laser diodes and filters used in DWDM transmission systems.

The Q8384 can also accurately measure the wavelength spacing of WDM signals because of its ±10 pm wavelength linearity over the 1530 to 1570 nm wavelength range.

50 dB (±0.1 nm)/60 dB (±0.2 nm) Wide Dynamic Range

In DWDM systems, signals need to be WDMed at intervals of 50 GHz (0.4 nm) or less.

Separating and measuring these closely spaced signals requires an optical spectrum analyzer with excellent dynamic range.

The Q8384’s dynamic range of 60 dB or more at 0.2 nm makes it ideal for this task.

With a dynamic range of 50 dB or more at 0.1 nm, the instrument can support future DWDM systems with closer signal spacing.

+23 dBm (200 mW) high-power direct input The Q8384 can directly measure high-power signals from fiber amplifiers or pump laser diodes without attenuation.

Extensive Analysis Functions

Sweep Function

The Q8384 displays the optical frequency on the horizontal axis; this is ideal for measuring the grid frequencies of standardized wavelengths specified by the ITU-T (International Telecommunication Union Telecommunication Standardization Sector).

Measuring the noise figure of a fiber-optic amplifier The Q8384 improves the noise figure of a fiber-optic amplifier by enhancing the dynamic range, polarization correlation, level accuracy, linearity, and accuracy of wavelength resolution settings.

As well as applying curve fitting and other features, the Q8384 realizes high-precision noise figure measurements at the touch of a button.

Since the Q8384 can accurately determine the ASE signal level of DWDM signals that are multiplexed at 10-minute intervals.

Since the Q8384 can accurately determine the ASE signal level of DWDM signals multiplexed at intervals of 50 GHz (0.4 nm) or narrower, it not only performs accurate noise figure measurements, but it can also accurately measure the noise figure of DWDM signals multiplexed at intervals of 10 minutes.

It not only performs accurate noise figure measurements, but also displays multiple lists of measurement results at the same time.

WDM Analysis Functions

The Q8384 can display up to 256 wavelength peaks and power levels of WDM signals.

It displays the deviation of the wavelength and power level from the ITU-T channel spacing or reference signal as well as the absolute value.

Alternate Scanning Function

The Q8384 can display two sets of measurements under different setup conditions in two windows. These windows are always rewritable using the Q8384’s alternate scan feature.

With this feature, users can make detailed measurements of signals in a specific wavelength band while monitoring the entire wavelength region of the WDM system.

Advantest D3286 Error Detector

D3286 Pulse Pattern Generator/Bit Error Detector

150 Mbps to 12.5 Gbps BER Performance Test System for SDH/SONET

D3286 Error Detector

SDH/SONET frame synchronization for system evaluation

Region-specific error detection for SDH frame and ATM cell measurements

Burst data measurement for loopback testing

Auto-search function to adjust the most suitable timing and voltages

Data and clock monitoring outputs

FD drive for storing measurement results and setup data

Graphical user interface (GUI) environment for an easy-to-understand operating environment

Ultra-high-speed digital telecommunication networks are being built to accommodate the transmission of high-capacity information in the multimedia era of the future.

To evaluate and analyze O/E and E/O modules and ultra-high-speed logic devices for multiplexers and repeaters in telecommunication systems

Evaluating and analyzing O/E and E/O modules and ultra-high-speed logic devices for multiplexers and repeaters in telecommunication systems requires the use of high-speed, high-quality signal sources.

The D3186 Pulse Pattern Generator/D3286 Error Detector provides excellent performance!

The D3186 Pulse Pattern Generator/D3286 Error Detector delivers excellent signals with high speed, high quality, and a variety of error-detection features over the 150 Mbps to 12.5 Gbps operating frequency range.

In addition, the D3186/D3286. with its 8 M-bit mass memory and ADVANTEST’s unique frame pattern generation capability, is the next generation of BER test systems.

The D3186/D3286 is a new generation of BER performance test systems compatible with STM-1 (155.52 M bps) to STM-64 (9.95 Gbps) in SDH/SONET.

Generates SDH/SONET Frame Patterns Close to Actual Data

For evaluating optical transport equipment, E/O and O/E modules

Frame-level testing is required for O/OE and E/O testing of SDH/SONET systems.

The D3186 Pulse Pattern Generator, in addition to having a large WORD memory of 8 M bits in length, provides a frame-level test in the STM frame header section.

The D3186 Pulse Pattern Generator, in addition to having a large 8 M-bit WORD memory, provides the optional functions of inserting a WORD pattern into the header portion of the STM frame and inserting an arbitrary PRBS into the payload portion, thus realizing a test pattern that is very close to the actual data.

Of course, the D3286 error detector can measure errors in the header and payload sections separately.

In addition, the D3286 has a frame synchronization function and a specific area error measurement function, which can effectively support the location of the cause of the error.

GE VMIVME-5576 Fiber Optic Reflective Memory with Interrupts

Features

– High-speed, easy-to-use fiber optic network (170 Mbaud serial rate)

– Data written to the memory of one node is also written to the memory of all nodes on the network

– Up to 2.000 meters between nodes, up to 256 nodes can be connected

– Data transfer rate of 6.2 Mbyte/s without redundancy

– Data transfer rate of 6.2 Mbyte/s without redundancy Data transfer rate of 3.2 Mbyte/s with redundancy

– Any node on the network can generate an outage in any other node on the network or in all network nodes with a single command

– Error detection – redundant transmission mode suppresses errors

– No processor overhead

– Processor is not involved in network operation

– Up to 1 Mbyte of reflected memory

– A24:A32:D32:D16:D8 Memory Access

– Single 6U VMEbus board

Introduction to the VMIVME-5576

– The VMIVME-5576 is a high performance, multiplexed VME-to-VME network. Data is transferred by writing to the on-board global RAM.

Data is automatically sent to all Reflective Memory board memory locations on the network.

Product Overview

-The Reflective Memory concept provides a very fast and efficient way to share data between distributed computer systems.

VMIC’s VMIVME-5576 Reflective Memory interface allows data to be shared between up to 256 independent systems (nodes) at rates of up to 6.2 Mbyte/s. Each Reflective Memory board can be configured with up to 256 nodes.

Each Reflective Memory board can be configured with 256 Kbytes to 1 Mbyte of on-board SRAM. local SRAM allows fast reads of stored data.

Write data is stored in the local SRAM and broadcast to other Reflective Memory nodes via a high-speed fiber optic data path.

Data transfers between nodes are software transparent, so there is no I/O overhead.

Transmit and receive FIFOs buffer data during peak data rates to optimize CPU and bus performance and maintain high data throughput.

Reflective memory also allows interrupts to one or more nodes by writing to byte registers.

These interrupt (tertiary, user-definable) signals can be used to synchronize system processes or to follow any previous data.

Interrupts always follow the data to ensure that the data is received before the interrupt is acknowledged.

The VMIVME-5576 does not need to be initialized unless interrupts are used.

If interrupts are used, vectors and interrupt levels must be written to on-board registers and interrupts must be set.

Each node on the system has a unique identification number between 0 and 255.

The node number is determined by placing jumpers on the board during hardware system integration.

The node number can be read by software by accessing the on-board registers. In some applications, the node number helps determine the function of the node.

GE DS200ITXDG1ABA Dynamic Brake Buffer Plate

About the DS200ITXDG1ABA

The DS200ITXDG1ABA board is labeled as a Dynamic Brake Buffer Board and is part of the Mark V Series manufactured by General Electric.

The Mark V Series, of which this DS200ITXDG1ABA product is a part, was one of the last of General Electric’s Mark product line to incorporate Speedtronic control system technology into its various products.

And since it was eventually discontinued many years after its initial release, it exists as a legacy product line.

This DS200ITXDG1ABA Printed Circuit Board, or PCB for short, is not an original development for its specific Mark V Turbine Control System family of functional roles; it is actually the DS200ITXDG1 Parent Dynamic Brake Buffer Board.

The DS200ITXDG1ABA PCB is conspicuously missing all three versions of the three important product versions of the DS200ITXDG1ABA PCB.

The assembly of this DS200ITXDG1ABA PCB has been specifically altered to utilize a Level A Major Function Revision, a Level B Minor Function Revision, and a Level A Drawing Configuration Revision.

Hardware Tips and Specifications

The required operation of the IXTD board is provided through the circuitry of the connected power supply/interface board (IMCP). When the IMCP and the IXTD board are connected, they are connected via a four-pin connector.

When the board is installed, it will be externally mounted and must be sized to meet the worst-case switching requirements of dynamically braked IGBTs.

The purpose of the snubber board is to be used to limit voltage transients at both ends of the IGBT and at all known operating conditions of the driver.

Another function of the DS200ITXDG1ABA board is to regulate the output of the IGBT gate driver board to match the electrical characteristics of the AT frame driver.

AT frame drivers are available in variable and constant torque applications. The drive output current rating for variable torque applications is 500 ARMS.

The DS200ITXDG1ABA board has three connector types: bus I/O connectors, input connectors for DBPL, and board pin connectors.

All of these connector types have different pin numbers, nomenclature, and descriptions, which are explained in depth and in detail in the DS200ITXDG1ABA instruction manual included above for your convenience.

Bus I/O connectors and pin I/O connectors are also oriented. Two examples of pins associated with the stab I/O connectors are the E-6 and E-9 connectors, both of which are output connectors.

The E-6 connector is the DB IGBT gate signal and the E-9 connector is the connection for the external buffer resistor.

The single plug-in connector that can be used to assemble this DS200ITXDG1ABA Dynamic Braking Buffer Board is also fully discussed in the associated General Electric instruction manual material.

This connector is accompanied by a DBPL factory printed naming label and connects this DS200ITXDG1ABA product to the accessible IMCP cousin PCB product in the larger Mark V series automatic drive assembly.

For convenience, the plug-in connector location for this DS200ITXDG1ABA PCB is described separately in the available guidance material.

Before making any single final purchase decision on this DS200ITXDG1ABA Dynamic Brake Buffer Board, it is important to realize that it was originally designed to be used as a dynamic brake buffer board.

It is important to realize that the performance specifications and dimensions it was originally introduced with have undoubtedly changed as a result of its receiving a full triple revision history.

The ITXD board allows for adjustment of the various outputs in the Mark VI series. There are three different connector types on the board, allowing the board to be connected in a variety of different ways.

This DS200ITXDG1ABA printed circuit board product or PCB for short has the normal style of Mark V series assembly, although it has been edited by accepting the full range of three Mark V series feature and illustration configuration product revisions.

GE Mark V Series DS200FCGDH1B Printed Circuit Boards

This DS200FCGDH1B printed circuit board product manufactured by General Electric was originally designed and manufactured for placement in its Mark V family of turbine control systems.

This DS200FCGDH1B printed circuit board, or PCB for short, is considered a member of the Mark V family.

It has specific applications in the management and control systems of popular and compatible wind, gas and steam turbine automatic drive assemblies, as evidenced by the full extended family name provided above.

This Mark V family of DS200FCGDH1B Printed Circuit Boards, or PCBs for short, while related to newly developed alternative energy technologies

must still be considered an obsolete GE legacy product line, as it was massively discontinued due to obsolescence many years after the release of the original Mark V line of products.

The Mark V series of this DS200FCGDH1B PCB, while generally obsolete due to its legacy series status, still offers many highly sought after products.

This is because it exists as one of the definitive General Electric Mark product lines, utilizing the company’s patented Speedtronic control system technology.

In addition, the DS200FCGDH1B PCB does not exist as the original development of its intended Mark V series functionality; this would be the case with the lack of the DS200FCGDH1B PCB.

This would be the DS200FCGDH1 female PCB that lacks the single Level B functional product revision of the DS200FCGDH1B product.

Hardware Tips and Specifications

The DS200FCGDH1B is a door assignment and status card (FCGD). Developed by General Electric for its Mark V board family, the card can be installed in many GE-branded drives.

Once installed, the card acts as the interface system for a six-pulse phase control non-inverting bridge. the DSPC (Digital Signal Processing Card) relays information to the board for decryption.

This generates signals about diagnostic information and system feedback. This generates signals for diagnostic information and system feedback, which are then sent out using the drive’s integrated VME backplane.

This DS200FCGDH1B product collects a large amount of data from the drive’s integrated DSPC.www.abb-drive.comThe signals received by the board are converted to unit gating signals.

All system bridge pins receive this cell gating signal and return multiplexed cell status information to the card. the FCGD board also receives and scales feedback signals.

The three FGPA boards send feedback signals through fiber optic connections on the board. The included feedback includes frequency, voltage, and board status information.

The integrated IMOK LED status indicator provides the user with basic system status.

Board installation parameters provided by the manufacturer should be met to minimize the risk of equipment failure or error. Board functionality is dependent on proper wiring of the system.

An illustrated guide for wiring and installing the DS200FCGDH1B is provided in the equipment manual and data sheet. The entire Mark V series was originally powered by General Electric.

The above additional information for this DS200FCGDH1B printed circuit board product is largely reminiscent of the general Mark V Series instruction documentation and visual inspection of the DS200FCGDH1B unit itself.

This strategy was deemed necessary due to the legacy series status of this DS200FCGDH1B product and the concomitant lack of on-line instructional manual material that could be utilized for research purposes on this page.

With this in mind, the DS200FCGDH1B functional product number itself can be considered an important source of information on DS200FCGDH1B Board hardware components and component specifications.

as it encodes a range of details in a series of consecutive function naming blocks.

For example, the DS200FCGDH1B Functional Product Number begins with a dual-function DS200 series label representing the normal Mark V series components of that DS200FCGDH1B product and its original domestic manufacturing location.

Some other relevant hardware details revealed through the use of the DS200FCGDH1B Functional Product Number include this Mark V Series PCB:

.FCGD Functional Product Abbreviation

.First Mark V Series Product Grouping

.Conformal pattern of PCB protective coatings

.Class B Functional Product Revision

The board has voltage controlled oscillators for analog feedback of current, voltage, and magnetic flux. These drive the VCO. The current and voltage signals can also be fed into the Sigma-Delta converter.

They operate in parallel with the VCO. Read through the relevant manuals for more detailed information about the motherboard, especially this one.

The base board of this DS200FCGDH1B PCB is protected by a thick, basic layer of daily wear protection provided by its conformal PCB surface coating.

Bently 2300/20 and 2300/25 2300 Vibration Monitors

Description

The 2300 Vibration Monitors provide cost-effective continuous vibration monitoring and protection capabilities for less critical and spared machinery. They are specifically

designed to continuously monitor and protect essential medium to low criticality machinery in a wide range of industries including: oil & gas, power generation, water

treatment, pulp and paper, manufacturing, mining, cement, and other industries.

The 2300 Vibration Monitors deliver vibration monitoring and high vibration level alarming.

They include two channels of seismic or proximity measurement inputs from various accelerometer, Velomitor and Proximitor types,

a speed input channel for time-synchronous measurements, and outputs for relay contacts.

The 2300/20 monitor features a configurable 4-20 mA output which interfaces more points to a DCS.

The 2300/25 monitor features System 1 Classic connectivity for Trendmaster SPA interface which enables users to leverage existing DSM SPA infrastructure.

The 2300 Vibration Monitors are designed for using on a broad range of machine trains or individual casings

where the sensor point count fits the monitor’s channel count and where advanced signal processing is desired.

Monitor Key Features

2300/20

l Two 4-20 mA outputs with internal current loop power supply.

l Continuous monitoring and protection

l Two acceleration/velocity/proximity inputs with synchronized sampling for advanced diagnostics.

l One dedicated speed channel supporting Proximity probes, Magnetic pickup and Proximity switch type sensors.

l Supports process variable on all three input channels.

l Key measurements (Acceleration pk,Acceleration rms, Velocity pk, Velocity rms, Displacement pp, Displacement rms,Speed) real-time provided with alarm configuration.

l Each channel has one measurement group, and can add additional two bandpass measurements and several nX measurements (depends on the device availability).

l LCD and LED for real time value and status display.

l Ethernet 10/100 Base-T communication for configuration using Bently Nevada Monitor Configuration software (Included) with RSA encryption.

l Local contacts for positive engagement of monitor bypass, configuration lockout,and latched alarm/relay reset.

l Two relay outputs with programmable setpoints.

l Three buffered transducer outputs (including Keyphasor signal) providing short circuit and EMI protection. Buffered outputs for each signal are through BNC connectors.

l Modbus over Ethernet.

l Alarm Data Capture

System 1 Evolution Connectivity

2300 monitors connect to System 1 Evolution and support current value and time-based data collection of all static values, waveforms,

and spectral data. This includes System1 Software’s full suite of plots and tools for condition monitoring and asset management.

When an alarm is triggered on the 2300 monitor, the following high-resolution alarm data is forwarded to System 1.

Bently 2300/25 2300Series Vibration Monitors

Description

The 2300 Vibration Monitors provide cost-effective continuous vibration monitoring and protection capabilities for less critical and spared machinery. They are specifically

designed to continuously monitor and protect essential medium to low criticality machinery in a wide range of industries including: oil & gas, power generation, water

treatment, pulp and paper, manufacturing, mining, cement, and other industries.

The 2300 Vibration Monitors deliver vibration monitoring and high vibration level alarming.

They include two channels of seismic or proximity measurement inputs from various accelerometer, Velomitor and Proximitor types,

a speed input channel for time-synchronous measurements, and outputs for relay contacts.

The 2300/20 monitor features a configurable 4-20 mA output which interfaces more points to a DCS.

The 2300/25 monitor features System 1 Classic connectivity for Trendmaster SPA interface which enables users to leverage existing DSM SPA infrastructure.

The 2300 Vibration Monitors are designed for using on a broad range of machine trains or individual casings

where the sensor point count fits the monitor’s channel count and where advanced signal processing is desired.

Monitor Key Features

2300/25

l Trendmaster SPA interface.

l Continuous monitoring and protection.

l Two Acceleration/Velocity/Proximity inputs with synchronized sampling for advanced diagnostics.

l One dedicated speed channel supporting Proximity probes, Magnetic pickup and Proixmity switch type sensor.

l Support process variable on all three input channels.

l Key measurements (Acceleration pk, Acceleration rms, Velocity pk, Velocity rms, Displacement pp, Displacement rms, Speed) real-time provided with alarm configuration.

l Each channel has one measurement group, and can add additional twoban dpass measurements and several nX measurements (depends on the device availability).

l LCD and LED for real time value and status display.

l Ethernet 10/100 Base-T communication for configuration using Bently Nevada Monitor Configuration software (included) with RSA encryption.

l ocal contacts for positive engagement of monitor bypass, configuration lockout,

and latched alarm/relay reset.

l Two relay outputs with programmable setpoints.

l Three buffered transducer outputs (including Keyphasor signal) providing short circuit and EMI protection. Buffered outputs for each signal are through BNC connectors.

l Modbus over Ethernet.

l Alarm Data Capture

System 1 Evolution Connectivity

2300 monitors connect to System 1 Evolution and support current value and time-based data collection of all static values, waveforms,

and spectral data. This includes System1 Software’s full suite of plots and tools for condition monitoring and asset management.

When an alarm is triggered on the 2300 monitor, the following high-resolution alarm data is forwarded to System 1.

Rexroth Pressure transducer HM20 R901466598

Features

▶ Measuring pressures in hydraulic systems

▶ 8 measurement ranges up to 630 bar

▶ Sensor with thin film measuring cell

▶ Components that are in contact with the media are made of stainless steel

▶ Operational safety due to high bursting pressure,reversed polarity, overvoltage and short-circuit protection

▶ Characteristic curve deviation <0.5%

▶ Non-repeatability <±0.05%

▶ Ambient temperature range –40 … +85 °C

▶ Marine approval DNV for all variants with current output

​Weight

kg 0.06

Nominal temperature range

°C –25 … +80

Ambient temperature range

°C –40 … +85

Storage temperature range

°C –40 … +80

Medium temperature range

°C –40 … +90

Sine test according to DIN EN 60068-2-6

10 … 2000 Hz/maximum of 10 g/10 cycles/3 axes

Noise test according to DIN EN 60068-2-64

20 … 2000 Hz / 14 gRMS / 24 h / 3 axes

Transport shock according to DIN EN 60068-2-27

15 g / 11 ms / 3 axes

Pressure port 1)

G1/4 threaded port according to DIN 3852 form E

Housing materials

V4A (1.4404), PEI, HNBR

Material process interface with measuring cell

1.4542 (17-4 PH / 630); seal ring NBR

Throttle material

1.4305

Throttle element

In the pressure channel of the process interface. It corresponds

to a nozzle of 0.3 mm and reduces the risk of damage during

highly dynamic effects such as pressure peaks or cavitation.

Rexroth R901342038 HM20-21/315-F-C13-0.50 Pressure sensors

Description

The Bosch Rexroth HM 20-2X/315-F-C13-05-N (R901342038) is a high-precision pressure

transducer designed for monitoring and controlling hydraulic pressures within a wide range of applications.

This sensor is capable of measuring pressures with ranges up to 600 bar,

making it suitable for various demanding environments where accurate pressure readings are critical.

The transducer features a thin film measuring cell and components that come into contact with

media are constructed from stainless steel, ensuring durability and compatibility with a variety of fluids.

With its excellent non-repeatability of less than 0.1% and an accuracy class of 0.5,

the HM 20-2X/315-F-C13-05-N provides reliable and precise measurements essential for maintaining system performance and safety.

The device also boasts operational safety features including high bursting pressure capacity,

reversed polarity protection, overvoltage protection, and short-circuit protection.

www.abb-drive.com This model operates within an extensive temperature range, ensuring consistent performance under varying environmental conditions.

Additionally, it has received marine approval DNVGL for all variants with current output,

which attests to its robustness and suitability for maritime applications.

The component series X to which this transducer belongs indicates

that it is part of a line designed to handle maximum operating pressures of up to 315 bar.

It offers pressure ratings at several intervals including 100, 160, 250, 315, 400, 600 bar etc.,

providing flexibility for integration into different hydraulic systems. Furthermore,

the HM 20-2X/315-F-C13-05-N is cULus-listed demonstrating compliance with

North American safety standards and regulations for industrial control equipment.

Features

Measuring pressures in hydraulic systems 8 measurement ranges up to 630 bar Sensor with

thin film measuring cell Components that are in contact with the media are made of stainless

steel Operational safety due to high bursting pressure, reversed polarity,

overvoltage and short-circuit protection Accuracy class 0.5 Excellent non-repeatability

< 0.05 % Wide operating temperature range –40 … +85 °C Marine approval DNV-GL for all variants with current output.

Search for products

Back to Top
Product has been added to your cart