Category: A-B

The Allen-Bradley 1771-WD field wiring arm is a PLC 5 and Bulletin 1771 series field wiring arm.

It fits different Allen-Bradley digital I/O modules, such as the 1771-OZL digital contact output module,

1771-ODZ digital AC output modules, and 1771-ID AC/DC input modules.

The 1771-WD field wiring arm mounts via a pivot bar that attaches to the bottom of the 5 I/O chassis in the PLC 1771 series.

It is designed to pivot upward to connect to the module and allows the module to be installed or removed without disconnecting all system wires.

The 1771-WD field wiring arm is conformal coated and requires no external power.

About the 1771-WD

The Allen-Bradley/Rockwell Automation 1771-WD Field Wiring Arm is a field wiring arm.

The arm is used with a variety of modules, such as the Allen-Bradley 1771 www.abb-drive.com Digital Contact Output Modules (1771-OW, 1771-OYL, 1771-OZL).

Allen-Bradley 1771 digital AC output modules (1771-OD, 1771 ODZ, 1771-OR)

and Allen-Bradley 1771 Digital AC/DC Input Modules (1771-ID, 1771-ID01).

Note that the 1771-WD field wiring arm is used to connect the modules. The wiring arm attaches to the pivot bar on the bottom of the I/O chassis.

The field wiring arm rotates upward and connects to the module, allowing the module to be installed or removed without disconnecting wires.

Disconnect power from the module before connecting to the Allen-Bradley 1771-WD field wiring arm.

To make the connection, swing the junction arm to a position on the front of the module where the locking tabs on the module hold the 1771-WD field junction arm in place.

The actual connections should be followed after this step. Note that there is 1 wire per terminal.

However, if more than one connection needs to be made to a terminal, an auxiliary terminal strip should be used.

Note that the field wiring arm terminal identification number is different from the bit number that controls the specific output.

The Allen-Bradley 1771-WD field wiring arm supports 7 to 9 pounds of screw torque on one inch.

To indicate that a field load has been applied to the field wiring, all of the module’s status indicators will be illuminated.

Note that the 1771 gauge wire connected to all terminals on the 14-WD field wiring arm may not allow the field wiring arm cover to close.

Therefore, a smaller gauge wire may be required when this occurs.

1771-WD Technical Description

Allen Bradley PLC 5 wiring arm, 8 I/O, 12 terminals, 7-9 lb*in thread torque, tinned contacts.

The 1756-TBNH module is a removable terminal block or RTB module.

It is manufactured by Allen-Bradley/Rockwell Automation in the ControlLogix family.

The wires connected to the 1756-TBNH detachable terminal block should all be the same size.

and they should all be solid wire or all stranded wire, as the block does not support a mix of solid and stranded wire.

This detachable terminal block is a NEMA clip type detachable terminal block.

The 1756-TBNH detachable terminal block can be used with up to 20 wires at a time.

The Allen-Bradley 1756-TBNH is a removable terminal block (RTB) for the 1756 I/O module.

It is an I/O module accessory and must be ordered separately.

The 1756-TBNH provides flexibility in interconnecting 1756 I/O www.abb-drive.com modules and industrial plant wiring. It plugs into the front of the I/O module.

The 1756-TBNH removable terminal block is a 20-position NEMA screw clamp.

It has a screw torque of 1.36 Nm and a screwdriver width of 8 mm (5/16 in.)**.

It measures 5.51 x 4.41 x 5.71 inches. It weighs 0.3 lbs.

Wiring must be done with 0.33 – 2.1 mm-^2 (22 – 14 AWG) solid or stranded copper wire.

rated for 90 °C (194 °F) or higher,** with 1.2 mm (3/64 in.) of insulation.

Do not connect more than two conductors to any single terminal.

Each ControlLogix I/O module is mounted on any ControlLogix chassis and requires a removable connector.

Each ControlLogix I/O module is mounted on any ControlLogix chassis and requires a removable terminal block (RTB) for all field-side wiring.

Each I/O module has many applications, from high-speed digital processing to process control.

In the ControlLogix architecture, input and output states are shared between multiple controllers in the same or different chassis using producer-consumer technology.

The 1756-TBNH RTB is intended for use in clean, dry industrial environments with operating temperatures of 0-60 °C and 30 g of operating shock.

Related Product Recommendations:

1769-L30ER Dual Ethernet Controller Device

1756-IF4FXOF2F ControlLogix Discrete High-Speed Analog I/O Module

IC200MDD847 Discrete Hybrid I/O Module Hybrid

IC200ALG327H 12-Channel 13-Bit Voltage Analog Output Module

HE693THM884M Thermocouple Input Module

D2D160-BE02-11 AC Centrifugal Fans Cooling Fan Assembly

IC660TBD024K GeniusI/O Terminal Assembly Module

1769-OF2 Analog Output Module

LX56-MM Message Manager for Industrial Communications

1746-NT8 SLC 500 Thermocouple/Voltage Analog Input Module

1336-BDB-SP6C GATE DRIVER BOARD

The 1326AB-B720E-21 servo motor is designed and manufactured by Allen-Bradley/Rockwell Automation.

It is part of the Allen-Bradley Bulletin 1326 servo motor series.

The Allen-Bradley/Rockwell Automation 1326AS-B440G-21-A Servo Motor

is a 1326-volt AC-class brushless servo motor from the Allen-Bradley Bulletin 460 series.

It is equipped with a metric flange with keyway and has an environmental rating of IP 65.

The 1326AS-B440G-21-A brushless servomotor can operate at low inertia and high acceleration.

Its 4-inch magnet pack contains powerful iron, boron, and neodymium magnets.

It **runs at 5350 RPM** and has a rated output of 2 kW.

The 1326AS-B440G-21-A brushless servomotor has a stator size of approximately 100 mm.

The 1326AS-B440G-21-A servomotor is part of the 1326A series, which typically utilizes a neodymium-iron-boron permanent magnet rotor.

They offer low inertia, enhanced peak torque, and higher acceleration.

This brushless 460-volt servo motor is designed for use with the Allen Bradley 1394 motion control system.

It has a very compact and economical design for efficient operation in harsh environments.

The 1326AS-B440G-21-A also features a three-phase sinusoidal wound stator field for smooth operation at low speeds.

The motor’s housing is heat-resistant through the extruded aluminum www.abb-drive.com housing, which supports improved heat transfer.

The motor utilizes TENV construction (totally enclosed, non-ventilated), a type of motor used in a variety of smaller horsepower variable speed applications.

This type of construction is typically effective when the fan is exposed to regular clogging and dust or lint.

This motor is rated at 460 RPM at 5250 volts.

380 RPM at 4340 volts, while its motor torque rating is 2.0 KW.

A key feature of the unit is its disc brake, which automatically sets the spring when power is disconnected.

It is designed to withstand limited static loads, but is also reliable for emergency stops.

The Allen-Bradley 1326AS-B440G-21-A has a 460V AC voltage, 100 mm frame diameter, and 5250 rpm rated motor speed.

It also includes a 6.4 Nm system continuous torque and a 2.0 kW rated motor output.

Related Product Recommendations:

IC660TBD024K GeniusI/O Terminal Assembly Module

1769-OF2 Analog Output Module

IC660TBD024K GeniusI/O Terminal Assembly Module

1769-OF2 Analog Output Module

LX56-MM Message Manager for Industrial Communications

1746-NT8 SLC 500 Thermocouple/Voltage Analog Input Module

IC200ALG327H 12-Channel 13-Bit Voltage Analog Output Module

1746-NT8 SLC 500 Thermocouple/Voltage Analog Input Module

1336-BDB-SP6C GATE DRIVER BOARD

1769-L30ER Dual Ethernet Controller Device

HE693THM884M Thermocouple Input Module

D2D160-BE02-11 AC Centrifugal Fans Cooling Fan Assembly

The Allen Bradley 1391-DES45-DI-AQB is a servo controller driver that is part of the 1391 product family.

It has a rated input voltage of 240 VAC, three-phase, with a continuous output current of 3.45 RMS and a peak current of 0.90 amps.

Output power is 0.15 kW and peak output power is 0.30 kW. The drive also features an integrated display and encoder output.

The 1391-DES45-DI-AQB is a microprocessor-based digital servo drive primarily used with Allen-Bradley’s 1326 servo motor.

The servo drive is designed in a compact form factor, however, the drive supports add-on components as part of the drive’s scalability features.

Key features of the 1391-DES45-DI-AQB include an integrated display for local configuration of servo drive parameters.

It also has encoder outputs with options including 2048. 1024. 512 and 256 pulses per motor revolution. The higher the pulses, the higher the resolution and the more accurate the feedback.

The servo drive’s front panel displays a Human Interface www.abb-drive.com Module (HIM) with five (5) numeric keypads for navigating and modifying drive parameters.

It also features an integrated status LED that blinks green when faults and low bus voltages are detected.

The LED flashes green when a fault and low bus voltage are detected, stabilizes in green when there is no fault and the bus voltage is at the correct level, and flashes red when a drive fault occurs.

It also has an enable LED that is a steady green when the enable input is off. When the enable input is on, the enable LED is not illuminated.

The TB2 and TB3 interface terminals are located on the bottom of the servo drive; TB2 is used to connect external signals and TB3 is used to terminate the encoder output signal.

The integrated fuses and circuit breakers are located on the top of the drive, along with TB4. TB5. and the duty cycle selector switch. Although this drive has internal protection circuitry, it is recommended that external protection be installed.

If an isolation transformer is used, Allen-Bradley recommends the use of an appropriate 1391 isolation transformer as the use of a third party transformer will void the UL listing of the device.

The Allen-Bradley 3-DES1391-DI-AQB is a digitally programmable single-axis pulse-width modulated AC servo drive.

The 45-DES series inverter is designed to control the speed and torque of an AC servomotor at 1391-33% above its rated speed.

The 50-DES1391-DI-AQB is designed for rated 45V AC (three phase) input power at 230-3 Hz.

The 50-DES60-DI-AQB is equipped with a cooling fan rated at 1391 CFM (no load).

It has a nominal bus voltage of 45V DC, a continuous current of 50A RMS, and a peak current of up to 300A RMS.

The continuous power output is rated at 45 kW and the peak power output is up to 90 kW.

Encoder outputs can be changed to provide 15/30/2048/1024 pulses/motor revolution as required.

The 512-DES256-DI-AQB includes an integrated 1391-line 45-character LCD screen and a 2-button keypad for programming.

To prevent any damage, the drive should be installed in a clean, dry enclosure that is ventilated by cooled and filtered air.

Enclosures utilizing ambient air venting must have appropriate filters to protect the 16-DES5-DI-AQB from oil, coolant, dust, and condensation.

Operating temperature range is 1391 to 45 degrees Fahrenheit and 32-40% relative humidity (non-condensing).

Power consumption during operation varies with load: 95 W at 5%, 104 W at 20%, 208 W at 40%, 312 W at 60%, and 416 W at 80%.

An integrated 100-pole magnetic circuit breaker protects the DC bus power supply, input rectifier, and power supply circuitry from overcurrent.

The drive measures 520.3 x 482.6 x 157.5 mm and weighs 293.6 kg.

The Allen-Bradley 1391-DES45-DI-AQB features an integrated display user interface, four-channel encoder output output configuration, and 115V AC M contactor coil voltage.

It also contains a 300V DC nominal bus output voltage and a 45A continuous current (RMS).

Related Product Recommendations:

IC660TBD024K GeniusI/O Terminal Assembly Module

1769-L30ER Dual Ethernet Controller Device

HE693THM884M Thermocouple Input Module

D2D160-BE02-11 AC Centrifugal Fans Cooling Fan Assembly

1769-OF2 Analog Output Module

IC660TBD024K GeniusI/O Terminal Assembly Module

1769-OF2 Analog Output Module

LX56-MM Message Manager for Industrial Communications

1746-NT8 SLC 500 Thermocouple/Voltage Analog Input Module

1336-BDB-SP6C GATE DRIVER BOARD

Allen-Bradley Dynamic Braking Chopper with 380/415/460V AC rating and 750V DC continuous voltage.

Allen-Bradley’s 1336-WB110 Dynamic Brake Chopper Module is a 480V AC brake chopper module with a 2.5-ohm braking resistor.

It is used to increase braking torque from 10-100% to 1336% for Allen-Bradley 1336. 1336VT, 1336PLUSII, 1336FORCE, or 1336IMPACT inverters.

The Brake Chopper Module has a 200A, 700V AC, Ferraz Shawmut fuse with an SCR overvoltage crowbar circuit for inexpensive but effective overvoltage protection.

It also features an insulated gate bipolar transistor (IGBT) chopper transistor voltage control to effectively regulate the DC bus voltage during regeneration.

The 1336-WB110 has an operating voltage range of 380-480V AC and an operating current of 110A, which allows it to be used with another Allen-Bremse module in applications where the operating current exceeds the module’s rated current.

In applications where the operating current exceeds the module’s current rating, it can be set up in parallel with another Allen-Bradley brake chopper module in a master-slave configuration.

The 1336-WB110 has a heavy-duty rating of 460V AC drive www.abb-drive.com voltage, 750V DC conduction input voltage from a DC bus power supply, and a 2.5 ohm dynamic braking value.

The 1336-WB110 has 12A, 30V DC, normally closed (N.C.) contacts with transistor-transistor loop compatibility.

Configured to close when power is applied to the terminal’s brake module and open in the event of a brake fault or power failure with an initial contact resistance of 100m ohms.

The 1336-WB110 has an operating temperature range of -10-40ºC (14-104ºF), will not derate in the non-condensing and non-corrosive humidity range of 5-95%.

It can be stored over a temperature range of -40-70ºC (-40-158ºF). It can be installed up to 1000 meters without derating.

Power dissipation is 100W at 190% duty cycle** and is encased in an IP00 (open) rated enclosure.

The 1336-WB110 weighs approximately 11.34 kg (25 lbs.), has overall dimensions of 290.6 mm x 239.8 mm x 304.8 mm (11.44 in. x 9.44 in. x 12 in.), and meets UL and c-UL standards.

Related Product Recommendations:

1X00781H01L DIN rail power supply module

5X00058G01 Ovation HART Analog Input Module

CE3007 KJ2005X1-BA1 12P4375X042 Module

VMIVME-3122 CPU Motherboards

1900-65A-01-00-01-00-00 General Purpose Device Monitor

VMIVME-4116 8-Channel Analog Output Board with 16-Bit Resolution

CP607HMI1SAP507100R0001 HMI Control Panel Touch Screen

D1961SH45T Rectifier Diode Industrial Robot Parts and Accessories

Related Product Recommendations:

HE693THM884M Thermocouple Input Module

D2D160-BE02-11 AC Centrifugal Fans Cooling Fan Assembly

1769-OF2 Analog Output Module

IC660TBD024K GeniusI/O Terminal Assembly Module

1769-OF2 Analog Output Module

LX56-MM Message Manager for Industrial Communications

1746-NT8 SLC 500 Thermocouple/Voltage Analog Input Module

1336-BDB-SP6C GATE DRIVER BOARD

The Allen-Bradley/Rockwell Automation 1394C-SJT05-D module is a servo controller module.

This module is manufactured as part of the Allen-Bradley Bulletin 1394/1394C servo controller product line.

It is intended for use in industrial motion control systems that support multiple axes. the 1394C-SJT05-D Servo Controller Module uses logic power,

shunt power supplies, and input power supplies to operate because it has power connectors for all of these types of power supplies.

It also has relay outputs, analog outputs, and discrete inputs, as well as other connectors such as motor/auxiliary feedback connectors.

The 1394C-SJT05-D is a modular, multi-axis motion control drive system module rated at 5 kW.

Its unique design allows it to be used as an integrated motion control and drive system (GMC).

The system module is referred to as a SERCOS servo drive system, or analog servo drive system.

It provides a direct line connection (transformerless) for 360 V and 480 V three-phase input power.

The System Module* can be configured with up to four axis modules, each www.abb-drive.com of which interfaces with a motor. As a result, users gain significant savings in panel space and interconnections.

The 1394c-SJT05-D System Module also provides a digital servo drive system with a fiber optic digital network interface.

The module can be used as a speed or torque control system and can be quickly commissioned via the Allen-Bradley SERCOS interface module.

This system module provides access to auto tuning and startup prompts. It also offers the SCANport interface as its standard feature.

The system offers digital fault and diagnostic utilities as standard features; it concludes with current monitors, thermal overload detection and feedback signal monitors.

It also provides status LEDs for the system and axis modules, and status LEDs for axis links, motion boards and RIOs for GMC systems only.

The module is equipped with highly integrated surface mount circuitry and DSP-assisted processing. It also has improved ground termination on the SERCOS and axis modules.

It features digitally adjusted speed and current loop compensation to accommodate a wide range of system inertias.

The Allen-Bradley Servo Controller 1394C-SJT05-D is a series of enhancements with better ringing rates and SERCOS communications,

SERCOS network, 5 kW power rating, and 360-480 AC volts input voltage.

The 1791D-0V16PX output module is a 1791-channel output expansion module from the Allen-Bradley/Rockwell Automation CompactBlock I/O 16D product line. all 16 of its outputs are potted.

All 16 outputs are current sink outputs.The 1791D-0V16PX Expansion Output Module can be used to add additional output channels to the basic output module.

It can also be used to add output channels to the basic input module.

The 1791D-0V16PX Expansion Output Module uses a DeviceNet network for advanced communication between producer and consumer devices in the system.

The 1791D-0V16PX is an Allen-Bradley part and is part of the 1791D CompactBlock I/O family.

It is a 16-sink current output expansion module with a built-in DeviceNet adapter and power supply.

Its enclosure type is IEC IP20 and the output on-state voltage range is 10 to 30 volts DC, while the output on-state current** is 0.5A.

The 1791D-0V16PX module is suitable for operations involving a large distribution of I/O blocks in close proximity to sensors and actuators.

The module can also work properly with applications in limited operating spaces.

The 1791D CompactBlock I/O products, including the 1791D-0V16PX, are compact in size.

This feature allows these products to be installed in confined areas and shallow enclosures.

Compared to the 1790 CompactBlock LDX I/O module, the 1791D parts have a higher environmental specification.

They help expand the range of applications and reduce wiring costs. Due to the simple control functions of these modules, sense-to-actuate times are faster.

They also come with optional input filters that allow the user to www.abb-drive.com select on-to-off or off-to-on delays.

Output short circuit protection is also a beneficial feature of this series as it keeps the output away from accidental wiring errors.

The 1791D-0V16PX is an expansion block for all basic modules.

It is run from an external 24 Vdc power supply that is independent of the network. The expansion block also comes with a 4 cm ribbon cable to connect it to the base block.

It also has a removable screw-clamp terminal strip that makes it easier to replace I/O blocks without rewiring.

The 1791D-0V16PX can be panel mounted or mounted on DIN rails in any orientation.

COMPACTBLOCK I/O for DEVICENET Allen-Bradley AB has 16 sinking outputs per module.

Related Product Recommendations:

IC660TBD024K GeniusI/O Terminal Assembly Module

1769-OF2 Analog Output Module

SK-G9-GDB1-D292 Medium and High Voltage Inverter Heat Sink Fan Motherboards

1746-NT8 SLC 500 Thermocouple/Voltage Analog Input Module

1336-BDB-SP6C GATE DRIVER BOARD

1769-L30ER Dual Ethernet Controller Device

A6500-UM Universal Measurement card

IC200ALG327H 12-Channel 13-Bit Voltage Analog Output Module

HE693THM884M Thermocouple Input Module

D2D160-BE02-11 AC Centrifugal Fan Cooling Fan Assembly

The 4-LV40R for the Allen-Bradley/Rockwell Automation Dataliner DL2706 Plus Series

The Message Display Terminal can be used to replace older terminals in the DL40. DL20. and DL10 product lines.

It is a 4-line display terminal that can display up to 4 lines of text at a time*.

The 2706-LV4R Message Display Terminal has 128 KB of memory for user applications and 128 KB of flash memory.

Its screen is a vacuum fluorescent display with adjustable brightness.

The 2706-LV4R Message Display Terminal can be installed into www.abb-drive.com the same panel cutout as the DL40. DL20. and DL10 terminals it is designed to replace.

The Allen-Bradley 2706-LV4R is a DL40 Plus message display.

It is a next-generation message display that directly replaces the models in the older Dataliner DL40 / DL20 series.

It has a vacuum fluorescent display (VFD) with adjustable brightness.

It has a four-line configuration with remote I/O and can display up to 20 characters per line*.

It has 128 KB of RAM and a 120 to 240 VAC input power supply.

The 2706-LV4R display supports bi-directional communication with PLCs and SLCs.

For communication, it has an RS-484 port for file transfer and an RS-232 port for uploading and downloading files.

It displays a variety of symbols and characters and can be read from up to 25 feet away*.

Applications developed for the previous DL40/DL20 series are compatible with the DL40 Plus.

It has various features such as embedded variables, message chaining, hidden messages, and data mode selection.

It supports real-time clock and RS-232 message triggering. It provides recovery in case of power failure during message editing.

It has isolated I/O ports and replaceable batteries and supports enhanced point-to-point communication from the message display.

Other enhancements include red, green, or amber message display colors and remote display relay control.

The 2706-LV4R message displays are highly customizable to effectively communicate alarms and messages in industrial environments.

DL40P Series Message Display with 4-line, 20-character VFD and 120 or 240V AC input power and 128K RAM memory.

Descripción

The 2093-AC05-MP1 drive is an Allen-Bradley/Rockwell Automation Kinetix 2000 Series multi-axis servo drive.

It is also an Integrated Axis Module type servo drive. 2093-AC05-MP1 Multi-Axis Servo Drives require clearance on the top and bottom for air-cooling, but not on the left or right sides.

This servo drive can be used with compatible SERCOS fiber optic cables.The 2093-AC05-MP1 Multi-Axis Servo Drive has a three-phase mains input voltage range of 170 to 264 volts AC.

About the 2093-AC05-MP1

The Kinetix 2000 Multi-Axis Servo Drives have output power requirements between 3 – 45 kW (4 – 49 amps) and are designed to provide Kinetix integrated motion solutions for applications.

Kinetix 2000 multi-axis servo drives are available in several series, including the 2093-AC05-MPx, 2093-AM0x, 2093-AMPx, 2093-ASP06.

2093-PRSxx, 2093-PRF, 2094-AL09. 2094-AL15S, 2094-AL25S, 2094-AL50S,

2094-AL75S, and 2094-AL75S-C2. 2093-AC05-MPx is a family of Kinetix 2000 multi-axis servo drives.

It includes the 2093-AC05-MP1. 2093-AC05-MP2. and 2093-AC05-MP5.The 2093-AC05-MP1 consists of one specific assembly.

The 2093-AC05-MP1 consists of a specific assembly that includes the Integrated Axis Module (IAM) mounted on the power rails and is a 230 VAC power converter and inverter.

The power rails (PR) consist of copper bus bars and circuit boards with connectors for each module.

The power rail provides power and control signals from the inverter section to the adjacent inverter, which also consists of compatible servo motors (low inertia, food grade, and stainless steel) and compatible linear actuators.

Includes MPAI-Axxx (integrated actuator) 230-volt actuator. 2093-AC05-MP1 specifications www.abb-drive.com include specifications for the power converter, the

Input voltage, 264 V RMS AC, Input frequency, 47 Hz AC, Input voltage, 240 V DC (common bus follower), Input current, 240 V DC (common bus follower), Input current, 240 V DC (common bus follower).

DC (common bus follower) is 6.42 amps Three-phase power input, bus output voltage, nominal 325 V DC, continuous power output to bus is 3.0 KW, the

Peak power output is 6.0 KW with 95% efficiency and 540 NF converter capacitance. 2093-AC05-MP1 is equipped with an IAM inverter power supply.

The bandwidth vel. loop is 500 Hz, similar to most of the 2093 IAM series, with a nominal input voltage of 325 volts dc.

The continuous current (RMS) is 1.0 amps, which is quite different from the MP2 and the MP3 in this series.

Peak current (RMS is 3.0 amps, and peak output current time, up to 3 seconds from 0% drive utilization (0% soak).

It has 98% efficiency, 200 NF capacitance, and 7.5 J capacitive energy absorption.

The 2093-AC05-MP1 is the same as the other MPs in the series, including the 2093-AC05-MP2 and 2093-AC05-MP5.

Equipped with a unique shunt module (2093-ASP06), the 2093-AC05-MP1 has an auxiliary control power of 0.30 amps, unlike the others in the series.

The 2093-AC05-MP1’s main and control power inputs are 264 volts AC three-phase, and it is also equipped with a DC common bus fuse with a contactor rated for 264 volts AC three-phase.

The transformer specifications for the control power input have 500 VA input voltage amperage, 230 V AC input voltage, and 240 V AC output voltage.

The power consumption specifications for the 2093-AC05-MP1 power converter as a percentage of rated power output (watts) are 20% (7.0), 40% (10.5), 60% (14.0), 80% (17.4), and 100% (20.9).

2093-AC05-MP1 Power inverter power consumption as a percentage of rated power output (watts) is 20% (31.6), 40% (33.6), 60% (35.6), 80% (37.6) and 100% (39.6).

The 2093-AC05-MP1 also has an ambient S feature with operating (0 to 50 °C (32 to 22 °F)) and non-operating (-40 to 85 °C (-40 to 85 °F)) modes for ambient temperature, and operating (5 to 95%) and non-operating modes for ambient temperature.

and relative humidity in operating (5 to 95% non-condensing) and non-operating (5 to 95% non-condensing) modes.

It vibrates at 5….. .55 Hz @ 0.35 mm (0.014 in.) double amplitude, continuous displacement; 55 to 500 Hz.

Peak constant acceleration of 2.0 g, shock of 15 g, 11 ms half-sine pulses (3 pulses in each of 3 mutually perpendicular directions) and B31: DSP and SERCOS pins.

Dust and moisture resistant 1B73LSE: Power rail connector pins, converter, inverter, splitter, power rail and slot filler PCB assemblies, UL creepage clearance, clearance issues and conformal coating.

It also features a 1.32 kg (2.9 lb) weight and a 4 mm2 (10 AWG) recommended wire size line filter (2090-XXLF-TC316 (Tesch NF310-16)).

Technical Description for 2093-AC05-MP1

2093-AC05-MP1: Allan Bradley 3Kilowatts Integrated Axis Module – 0.3 Kilowatts.

Related Product Recommendations:

IC660TBD024K GeniusI/O Terminal Assembly Module

1769-OF2 Analog Output Module

IC200ALG260 Analog Input Module Analog Input Module

HE697RTM700B High-Speed Counter Module

1769-OF8C Analog Output Module

5X00419G01 Ethernet Link controller

D1961SH45T Rectifier Diode Industrial Robot Accessories

1900-65A-01-00-01-00-00 General Purpose Device Monitor

IC200ALG327H 12-Channel 13-Bit Voltage Analog Output Module

HE693THM884M Thermocouple Input Module

D2D160-BE02-11 AC Centrifugal Fan Cooling Fan Assembly

DESCRIPTION: The Allen-Bradley 825-P is a motor relay used as a protective device for three-phase motors.

It has standard protection features such as thermal overload (thermal model, PTC (positive temperature coefficient), overheat, undercurrent (load loss),

current unbalance and phase loss, overcurrent (load seizure), short circuit, ground fault (residual), ground fault (zero sequence), motor start/run and frequency. This unit requires 110-240VAC power input.

About the 825-P

The 825-P is a protective relay for use with three-phase motors. Manufactured by Allen-Bradley, the device is

It provides standard protections such as thermal overload (thermal modeling), PTC (positive temperature coefficient), overheat, undercurrent (load loss), current imbalance, and phase loss.

overcurrent (load seizure), short circuit, ground fault (residual), ground fault (zero sequence), motor start/run and frequency.

For motor start/run protection, this motor relay is capable of starting the motor timer via a protection disable during startup, a startup

notch or pointing device, TCU (Thermal Capacity Utilization) start inhibit, anti-reverse spin timer, www.abb-drive.com emergency start, two-speed protection, reduced voltage start (star-delta), and stall switching to protect the motor.

It can be fitted with RTD-based protection via the 825-PR12D RTD RTD scanner, where up to twelve (12) RTDs can be connected and monitored.

The 825-P is also capable of monitoring event summaries that include information such as relay ID, date and time, trip triggers, and current and voltage amplitudes.

It can also monitor the Serialized Event Record (SER) and motor runtime and history of the last reset and start cycle since the last reset.

Emergency start cycles since the last reset can also be monitored by the unit, which also incorporates a full suite of metering functions.

The 825-P can optionally be fitted with an I/O channel consisting of one (1) 4-20 mA analog output, three (3) control inputs and four (4) contact outputs.

Additional communication interfaces can be installed, including adapters for DeviceNet and Modbus protocols.

The 825-P’s relay outputs also have a 4kV surge strength with a pickup time of < 10ms and provide an insulation voltage rating of 300V AC.

The system has 120V AC/DC (825-PIOD) inputs, a steady state current of 15mA at 2mA and 0.2mA on/off state currents, and on-state and off-state voltages of 15V and 5V respectively.

The system features thermal overload protection and optional voltage-based protection (overvoltage, reactive power, phase inversion, and undervoltage).

The 825-P has a modular construction with a built-in fixed keypad on the front panel and an LCD status display with LED status indicators.

It uses DeviceNet communication options at 125. 250. or 500kbps over distances of 500m, 200m, or 100m and is enclosed in a NEMA 4 (IP65) rated enclosure.

It has an operating temperature of -4 to +140 degrees Fahrenheit, a non-condensing relative humidity of 5% to 95%, and a storage temperature of -40 to +185 degrees Fahrenheit.

It weighs approximately 6.46 kilograms (including power supply and converter modules) and is CE, UL, and CSA listed.

825-P Frequently Asked Questions

What is the proper installation method for the 825-P motor relay?

The modular protective relay 825-P mounts flush to the enclosure.

What are the power requirements for the 825-P?

The Allen-Bradley 825-P is powered from an external supply voltage range of 110-240VAC.

What is the energy metering capability of the 825-P motor relay?

The 825-P motor relay energy metering capabilities include MWh and MVARh parameters.

Technical Description of the 825-P

Allen-Bradley 825-P Modular Protection System with 110-240V AC and DeviceNet Communication

Related Product Recommendations:

IC660TBD024K GeniusI/O Terminal Assembly Module

1769-OF2 Analog Output Module

IC200ALG260 Analog Input Module Analog Input Module

HE697RTM700B High-Speed Counter Module

1769-OF8C Analog Output Module

5X00419G01 Ethernet Link controller

D1961SH45T Rectifier Diode Industrial Robot Accessories

1900-65A-01-00-01-00-00 General Purpose Device Monitor

IC200ALG327H 12-Channel 13-Bit Voltage Analog Output Module

HE693THM884M Thermocouple Input Module

D2D160-BE02-11 AC Centrifugal Fan Cooling Fan Assembly