Category: GE

About IC200ALG431

The IC200ALG431 module is a hybrid module from Agfaq. It is a 12-bit device for industrial automation applications.

The analogue module provides flexibility by combining inputs and outputs using a single carrier base.

The front of the module has LED indicators that help the operator understand the flow of power in the module.

The module has “FLD PWR” and “OK” LED indicators. The module is compact in size with a width of 4.30 inches, a depth of 1.95 inches and a height of 2.63 inches.

The IC200ALG431 module weighs approximately 4.4 lbs. The module is equipped with a 0 to 10 volt DC analogue input www.abb-drive.com and a 0 to 10 volt DC analogue output. The module is powered by an external power supply.

The IC200ALG431 module uses shielded twisted pair cable for analogue channel connections.

During module installation, the module should be properly grounded to the source device.

If the module is connected through a carrier using a connector type, it can be connected to the plug-in terminals.

Hybrid modules are equipped with diagnostics that help report circuit faults. The I/O defaults in the module can be used with jumpers.

The IC200ALG431 module draws a total of 60 mA from the 5 volt bus interface unit.

The module can be easily installed into a system by using panel mounting.

This is an indoor unit designed with an open architecture. It should be protected from water spray and kept away from heat sources.

The ambient temperature should not exceed 60 degrees Celsius.

Technical description of IC200ALG431

The IC200ALG431 module is an Agfanac module in the Versamax series. It is a 12-bit module.

Specification

Part Number: IS420UCSBH1A

Manufacturer: General Electric

Country of manufacture: USA

Product Type: UCSB Controller Module

Series: Mark VIe

The IS420UCSBH1A is a UCSB controller module developed by General Electric.The UCSB controller is a stand-alone computer that performs application-specific control system logic.

UCSB controllers are stand-alone computers that execute application-specific control system logic. Unlike conventional controllers, UCSB controllers do not carry any application I/O. In addition, all I/O networks are connected.

In addition, all I/O networks are connected to each controller to provide all input data.

The hardware and software architecture ensures that no single point of application input is www.abb-drive.com lost if the controller is powered down for maintenance or repair.

Operation

The controller comes preloaded with application-specific software. It can run ladders or blocks. Minor changes to the control software can be made online without rebooting the system.

The IEEE 1588 protocol is used to synchronise the clocks of the I/O components and the controller to within 100 microseconds via R, S, and T IONets.

External data is transferred to the controller’s control system database via R, S and T IONets.

Process inputs and outputs for the input/output modules are included.

The following are also included in a dual system:

Internal state values and initialisation information for the specified controller

State and synchronisation information for both controllers

Also includes the following in a triple-module redundant (TMR) system:

Internal state values for voting and status, and synchronisation information from all three controllers

Initialisation data from the specified controller

Advantages of the IS420UCSBH1A

The UCSB controller offers the following advantages:

A single module

Built-in power supply

No jumper settings required

No batteries

No fan

Smaller panel footprint

Flash memory can be easily updated

The UCSB controller is panel mounted and communicates with I/O components through an on-board I/O network (IONet) interface.

IONet is a private Ethernet network that supports only Mark control I/O modules and controllers.

Features

Microprocessor: 600 MHz Intel EP80579

Memory: 256 MB DDR2 SDRAM with Error Correcting Code (ECC), Flash support for SRAM, NAND flash size of 2 gigabytes

Operating System: QNX NeutrinoQNX Neutrino

Weight: 2.4 lbs

Mounting

The UCSB controller is mounted in a module that can be mounted directly to a panel metal plate.

The UCSB controller should be panel mounted to prevent vertical airflow through the heat sink.

WOC’s industrial automation hardware products include UCSB controller modules.

The experts at World of Controls are ready to help you meet your GE Mark VIe requirements.

Product Description

The General Electric Serial Modbus Communication Interface Pack IS220PSCAH1A is an I/O block that

It has six configurable serial channels that support multiple ports. The ports used with the IS220PSCAH1A block are RS422. RS485 half-duplex, and RS232 ports.

The IS220PSCAH1A I/O block is used for serial Modbus communication. This kit was designed by General Electric for the Mark VIeS control system.

When the package is used, it provides an interface between up to www.abb-drive.com two input/output Ethernet and a serial communications board.

The board has six individually configurable serial transceiver channels for use with RS485 half-duplex, RS232 and RS422 standards.

The inputs required to supply power to the PSCA block are sent through a three-pin power input and dual RJ45 Ethernet connectors.

There is a serial Modbus master service on the IS220PSCAH1A package with many different functions, some of which are listed below:

RTU Inc.

Data bits: seven, eight

32-bit data word ordering

Parity: even, none, odd

Station address

These functions are used for the six configurable ports on the PSCA block. They can be configured at the port level.

With PSCA, the two Ethernet ports on the block can be used to help support the Ethernet Modbus master protocol; note that this configuration can only occur when used on a simplex network.

The IS220PSCAH1A package has the ability to perform self agnostic tests, one of which is to monitor analogue inputs, the

used to monitor position and pressure to check for configurable high and low levels.

These limits are used to enable and disable functions, lockout/non-lockout, and generate alarms.

The possible alarms are 32-67. 114-119. 108-113. and 72-107.All of these alarms indicate different errors.

The GE Fanuc IC200CPUE05 is a VersaMAx controller module. The controller has a versatile design with 64 KB of configurable user memory.

It has one (1) RS232. one (1) RS485. and one (1) Ethernet communication port embedded.

The controller has a Boolean execution speed of 0.8 ms/K (typical) and supports up to 64 modules or 2048 I/O points.

About the IC200CPUE05

The GE Fanuc Versamax IC200CPUE05 CPU module is equipped with a supercapacitor capable of powering the memory for up to an hour.

There are run/stop switches in the module to control operations. the CPU is capable of handling floating-point data functions.

The CPU module is equipped with two sets of LEDs in the upper and lower right corners, with PWR, OK, RUN, FAULT, FORCE, PORT 1 and PORT 2 LEDs.

It has PWR, OK, RUN, FAULT, FORCE, PORT 1 and PORT 2 LEDs that light up when power is applied to the module and send different update messages to the user.

The IC200CPUE05 CPU module can be programmed using the ladder diagram and instruction list programming languages.

The CPU has an EGD time synchronisation function and supports up to 8 SRTP server connections.

The IC200CPUE05 is a central processing unit (CPU) module that is part of the VersaMax programmable logic controller (PLC) product family.

This CPU, also known as a controller, is used to execute downloaded logic into the CPU’s memory.

This CPU has a compact form factor, supports horizontal or vertical mounting to DIN rails, and is highly scalable.

The IC200CPUE05 has 64 KB of user-configurable memory and can handle up to 64 modules or up to 2048 I/O points.

It embeds one (1) 232-pin D connector supporting the RS9 standard, one (1) 485-pin D connector supporting the RS15 standard, and one (1) 485-pin D connector supporting the RS15 standard.

It embeds one (1) RS9-compliant 232-pin D connector, one (1) RS15-compliant 485-pin D connector, and one (1) Ethernet communication port that supports 10Mbps transfer rate, full and half duplex.

capable of up to eight (8) SRTP connections and thirty-two (32) configuration-based Ethernet Global Data (EGD) exchanges.

The IC200CPUE05 supports floating-point data formats and has a typical Boolean www.abb-drive.com execution speed of 0.8ms/K. It also has a built-in supercapacitor.

It also features a built-in supercapacitor that provides up to 1 hour of data retention before transferring backup protection to a battery capable of up to 6 months.

When not in use, the installed battery has a shelf life of up to 5 years.

The IC200CPUE05 is available in several revisions. These revisions include CPUE05-BE FW 2.2. which supports 32-bit register data for Modbus RTU masters.

CPUE05-AD FW 2.31 which supports MODBUS Master; CPUE05-AC FW 2.30 which adds support for MODBUS Master.

CPUE05-AB FW 2.20 has additional serial I/O baud rate; CPUE05-AA FW 2.10 is the initial product version.

The IC200ALG620 is a 4-channel resistance temperature detector (RTD) input module for the VersaMax I/O family.

Formerly manufactured by GE Intelligent Platforms, it is now manufactured by Emerson Automation.

With four (4) RTD inputs, the module is compatible with 3-wire or 4-wire RTD devices, and supports different types of RTD sensors

such as platinum 25. 100 and 1000 ohms; copper 10. 50 and 100 ohms; nickel 100 and 120 ohms; and nickel/iron 604 ohms.

and Ni/Fe 604 ohm and direct measurement resistance values including 0-500 ohm and 0-3000 ohm.

The module has a conversion resolution of 16 bits. el 100 and 120 ohms; and nickel/iron 604 ohms. The module has a 16-bit conversion resolution.

About the IC200ALG620

The IC200ALG620 is a VersaMax analogue input module manufactured by Emerson Automation.

The module is specifically designed for temperature measurement and sensor integration with resistance temperature detector (RTD) modules.

The module is a 4-channel RTD/resistance analogue input module that can be www.abb-drive.com used with a variety of RTD sensors.

including platinum 25. 100. and 1000 ohms; copper 10. 50. and 100 ohms; nickel 100 and 120 ohms; and nickel/iron 604 ohms, and direct input resistance value ranges such as 0-500 ohms and 0-3000 ohms.

The IC200ALG620 supports both 3-wire and 4-wire RTD sensors. Each channel has a dedicated analogue-to-digital (ADC) converter circuit with 16-bit conversion resolution.

The module has a measurement accuracy of +/-25.0% (at 15 degrees Celsius) for resistance measurements and +/-0.15% in RTD (temperature) measurement mode.

Each input channel is capable of detecting open RTDs, input shorts, under-range, over-range, non-volatile memory storage faults, wiring faults and high/low alarms.

These faults and alarm conditions are reported to the host programmable logic controller (PLC) for integration.

The module has an update rate of 60 ms per channel at 210 Hz and 50 ms per channel at 230 Hz.

It is also fitted with an OK LED which indicates backplane power supplied to the module when green is lit and module failure when amber is lit.

The module has a backplane current draw of 0 mA at 125.5 VDC bus output and 3 mA at 125.3 VDC bus output.

The IC200ALG620 module is a 16-bit module manufactured by GE Fanuc. It is an analogue input module designed with 4 channels.

It provides 16-bit resolution. It runs on 5 volts and has an update rate of 210 ms.

It is equipped with LED indicators that help the user to know the different status of the module. It has FLD PWR LED and OK LED.

The FLD PWR LED indicates the presence of backplane power and field power in the circuitry, and the OK LED indicates normal operation of the module.

It lights up in amber when there is a diagnostic error in the module. The LED flashes green when the module is being updated or is in startup mode.

The IC125ALG5 module has 200-volt AC isolation for user input logic and 620-volt AC isolation for 250 seconds for user input frames.

It draws a total of 1500 mA. It can be updated at 60 to 125 Hz, depending on the channel.

The module has a common-mode rejection ratio of 50 dB at 60 to 120 Hz over a 50% span.

Normal mode rejection is 60 dB at similar frequencies.The IC100ALG60 module should not exceed 200 degrees Celsius operating temperature in a clean environment.

The IC620ALG60 module is easy to configure and install. During installation, the module should be properly grounded to avoid electrical damage

GE VersaMax DataPanels are ideal for a variety of applications, from simple timer/counter/register access to full-text information displays with numeric keypads.

All VersaMax DataPanels are pre-programmed to quickly connect to a VersaMax Micro or Nano PLC without user configuration.

The GE Fanuc IC200DTX650 terminal is a data panel manufactured by GE Intelligent Platforms/GE Fanuc.

It is part of the Versamax family and can hold up to 200 stored messages.

About the IC200DTX650

GE Fanuc manufactures the IC200DTX650 data panel as part of the GE Versamax series.

The operator interface of this data panel has a **storage capacity** of up to 200 stored messages.

The dimensions of the IC200DTX650 Data Panel are approximately 96 x 96 x 50 mm.

All Versamax series data panels, including the GE Fanuc IC200DTX650 Data Panel

are suitable for a variety of applications such as counters and simple timer applications.

In addition, these data panels are compatible with the Record Access Full Text Message display.

The IC200DTX650 Data Panel features an LCD and LED display with backlighting, a www.abb-drive.com numeric keypad for data entry, and eight function keys.

The LCD on this panel can display 4 lines of text with up to 16 characters per line*.

The GE Fanuc IC200DTX650 data panel operates on a rated external power supply, rated at 24 volts DC and 80 milliamps.

To operate, this data panel requires the IC200CBL550 cable or equivalent.

The data panel has an active life cycle status and has an operating temperature range of 0 to 50 degrees Celsius.

It also has a NEMA 4 enclosure rating.

The IC200DTX650 data panel is a perfect match for the Data Designer (IC752DDZ000) software used for configuration purposes.

Typically, the Versamax product line offers universally distributed inputs and outputs covering PC and PLC based architectures.

These data panels are designed for commercial and industrial automation, and Versamax I/O also offers a versatile and flexible input and output architecture for remote and local control applications.

Related Product Recommendations:

DS200CVMAG3AEB Generator Control Turbine Boards

5X00070G03 Analogue High Speed Input Module

DS200ACNAG1 Computer Network (ARCNET) Boards

DS200CPCAG1A Contactor Boot Card

DS200DSPCH1 Processor Control Board

DS200DSPCH1A Digital Signal Processor Control Board

DS200FGPAG1AKD Control Gate Pulse Amplifier Board

5X00785G09 Power supply System

DS200GGDAG1AHE Gas Turbine Gate Driver

DS200CPCAG1ABB Contactor Guide Boards

1C31234G01 Compact Contact Input Module

DeltaV™m VerticalPlus Input/Output Subsystem Carrier

VMIVME-4140-001 VMIVME4140 16-channel 12-bit analogue output board

The GE Fanuc IC200MDD846 module is a hybrid I/O module.

It is manufactured by GE Fanuc and is part of the Versamax product family. It helps increase device flexibility by integrating discrete input and output points into a single module.

About the IC200MDD846

The GE Fanuc IC200MDD846 Hybrid I/O Module is a GE Fanuc product that is part of the Versamax family.

The module is designed to increase machine flexibility by integrating discrete input and output points into a single module.

For the module to operate efficiently, the IC200CHSxxx carrier base is required.

The IC200MDD846 hybrid module has a set www.abb-drive.com of 8 input points that draw current from the input devices connected to it and send it to the common line.

It also has a set of 8 output points with 8 output points capable of handling 2 Amp** current loads.

The input points of this hybrid module are positive logic type or source line type inputs, while the output points are type A relays which come with silver contacts, fixed coils and moving frames.

Each output point of the IC200MDD846 module is isolated. The module also features LED indicators corresponding to each input and output point.

The LEDs indicate that the device is switched on and off, while the ‘OK’ LED indicates the presence of baseboard power.

The IC200MDD846 Versamax Hybrid Module draws all necessary power from the rack mount backplane.

It is rated to supply 300 mA** and has a nominal input voltage of 120 volts AC.

It also has nominal output voltages of 5 volts DC, 24 volts DC or 125 volts DC and 120 volts AC or 240 volts AC.

The module has a voltage drop of 0.3 volts. A network interface unit or CPU is required to perform device processing.

The Discrete Hybrid Module combines inputs and outputs in a compact module to provide maximum flexibility.

Discrete input modules receive signals from input devices such as sensors, pushbuttons, and switches.

Signals from input devices such as pushbuttons and switches that have two states: on or off, open or closed.

Discrete output modules send control signals to devices that also have two states, such as contactors, indicator lights, and intermediate relays.

Discrete hybrid modules combine inputs and outputs in a compact module, thus providing maximum flexibility.

Output modules that offer maximum flexibility. Module requires a carrier base (IC200CHSxxx)

Related Product Recommendations:

1X00781H01L DIN rail power supply module

CE3008 Digital Output Module

DS200AAHAH2A Driver Board

5X00058G01 Ovation HART Analogue Input Module

DS200ACLEH1 Hub LAN Driver Boards

DS200ACLEH1B Hub LAN Driver Board

CE3007 KJ2005X1-BA1 12P4375X042 Module

1C31234G01 Compact Contact Input Module

DeltaV™ VerticalPlus Input/Output Subsystem Carrier

DS200ACNAG1 Computer Network (ARCNET) Boards

VMIVME-4140-001VMIVME4140 16-Channel 12-Bit Analogue Output Board

Related Product Recommendations:

DS200CVMAG3AEB Generator Control Turbine Boards

5X00070G03 Analogue High Speed Input Module

DS200ACNAG1 Computer Network (ARCNET) Boards

DS200CPCAG1A Contactor Boot Card

DS200CPCAG1ABB Contactor Guide Boards

1C31234G01 Compact Contact Input Module

DeltaV™m VerticalPlus Input/Output Subsystem Carrier

VMIVME-4140-001 VMIVME4140 16-channel 12-bit analogue output board

DS200DSPCH1 Processor Control Board

DS200DSPCH1A Digital Signal Processor Control Board

DS200FGPAG1AKD Control Gate Pulse Amplifier Board

5X00785G09 Power supply System

DS200GGDAG1AHE Gas Turbine Gate Driver

The IC200ALG264 is a 15-point analogue current input module for the VersaMax I/O family, formerly manufactured by GE Intelligent Platforms and now manufactured by Emerson Automation.

The module features fifteen (15) single-ended input channels that accept 4-20 mA and 0-20 mA input signals with 15-bit resolution** and an update rate of 7.5 ms.

The module has a **backplane current consumption of 100 mA.

About the IC200ALG264

The IC200ALG264 is the analogue input module in the VersaMax I/O product family of distributed I/O modules and components.

The IC200ALG264 is a compact, multifunctional input module designed to be mounted in a remote location and transmit I/O data via industrial communication protocols.

The module primarily features fifteen (15) analogue input channels designed to accept 0-20 mA and 4-20 mA input signals.

These input channels are equipped with separate analogue-to-digital converter (ADC) www.abb-drive.com circuits with a digital conversion resolution of 15 bits and an analogue resolution of 0.5 µA.

The analogue resolution is 0.5 µA = 1 (4-20 mA range) and 0.625 µA = 1 count (0-20 mA range).

The module has an input accuracy of +/-0.5% (typical) and +/-0.25% of full scale** at an ambient temperature of 0-3 degrees Celsius.

+/-0.5% input accuracy (typical) and +/-0.25% full scale** at 0-3 degrees Celsius ambient temperature, and +/-60% full scale** at 1-0 degrees Celsius ambient temperature.

The IC200ALG264 is capable of detecting error conditions such as internal power loss in both operating modes and open circuit detection when operating in 4-20 mA mode only.

These diagnostic conditions are reported to the CPU for error indication and correctly displayed to the Human Machine Interface (HMI) and Supervisory Control and Data Acquisition (SCADA) systems.

The module’s operating mode or range selection is set by using terminal jumpers. To configure 4-20 mA, the terminal jumpers must be unloaded, which is the default configuration.

Otherwise, install the jumper for 0-20 mA operation.

The IC200ALG264 has a built-in module OK LED status indicator.Tis LED indicates that the module has successfully powered up and downloaded using a valid configuration.

It has a ** backplane current consumption of 100 mA.

The IC200ALG264 module is an analogue input module designed and marketed by GE Fanuc Automation.

This particular module is part of the Versamax family of I/O modules. It provides interfaces for 15 different current inputs, enabling different devices to be connected to the main processor.

The module works perfectly when using the backplane power supply. User transceivers connected to the module require an external power supply.

The GE Fanuc Automation IC200ALG264 analogue input module offers different diagnostic functions that can detect internal power losses used for field circuits.

It can also report open-circuit faults on each of its channels. These diagnostic modes are available when used in 4-channel 20 mA mode.

The GE Fanuc Automation IC200ALG264 analogue input module comes with a set of 15 single-ended channels.

The module has isolation ratings of 350 volts AC continuous and 1500 volts AC one minute.

It has no isolation between channels and because the channels are in a single group. the GE Fanuc Automation IC200ALG264 analogue input module has a 15-bit resolution.

Typical accuracy is +/- 3.25% at 0 degrees Celsius and +/- 1% accuracy at full scale**.

The module’s backplane current consumption is rated at 5 mA at 100 volts**. The update time is rated at 7.5 milliseconds.

The module has an LED to indicate when power is applied to the backplane and when the module has been configured and identified on the backplane.

The IC200CHS002 is a compact I/O carrier module. It is part of the VersaMax platform.

currently part of Emerson Automation and formerly manufactured by GE Intelligent Platforms (GE IP).

It is a compact boxed I/O carrier with 18 terminals from A36 – A1 and B18 – B1.

The carrier can accommodate voltage ranges up to 0-264 VAC at 2 amps per point or 8 amps per power and ground.

The appropriate wire size for each terminal is solid or stranded copper, ranging from AWG # 14 to AWG # 22.

AWG #14 to AWG #22 for single wire connections and AWG #18 for two (2) wire connections in a single terminal for terminal shorting.

The module is designed for horizontal mounting.

About the IC200CHS002

The IC200CHS002 is a VersaMax I/O carrier module. The module offers a modular approach because it allows for servicing,

troubleshooting, and replacement of I/O modules without removing existing wiring terminals.

Typically, this carrier module provides installation and field wiring as well as backplane communications for hosted modules.

The module primarily has 36 terminals arranged in two (2) strips labelled A1 through A18 and B1 through B18.

The module is compatible with 32-point I/O modules or high-density I/O devices in the same VersaMax product family.

The module has 4 common/power connections and embeds keying dials that are set to match the designated keying positions of the module hosting the I/O carrier.

The hardware also has carrier mating connectors for quick assembly and connection to the backplane. It also features a module latch hole for locking the hosted IO module into place.

The terminals of the IC200CHS002 are capable of withstanding transient voltages up to 300 VAC.

During normal operation, each terminal is designed for a voltage range of 0-264 VAC and a current rating of 2 amps per terminal and 8 amps per power/common terminal.

Each terminal supports termination of up to 2 wires* with recommended wire sizes from AWG # 14 (average 2.1mm2 cross section)

to AWG #22 (average 0.36mm2 cross section) for single wire connections, AWG #18 (average 0.86mm2 cross section)

Used to connect two (2) wires in a single terminal for terminal shorting.

The GE Fanuc IC200CHS002 carrier is a Versamax series boxed terminal I/O carrier.

Designed for industrial automation applications, Versamax products provide a versatile and flexible I/O structure for local/remote configurations.

There are 3 types of I/O carriers in the Versamax product line, they are Terminal Carriers, Compact Terminal Carriers and Connector I/O Carriers.

The IC200CHS002 carrier has 36 IEC box terminals.The IC200CHS002 carrier provides backplane communications, mounting connections, and field wiring for one I/O module.

The dimensions of the IC200CHS002 carrier are 110.5 x 70 x 139.7 mm.

The terminals on the IC200CHS002 carrier are compatible with solid/stranded copper wire with a cross-sectional area of 0.36 to 2.1 square millimetres, or 86 conductors with a cross-sectional area of 2.0 square millimetres.

Copper wire rated to 194 degrees Fahrenheit is recommended for use with the Versamax IC200CHS002 carrier module.

Recommended terminal torque for the IC200CHS002 bracket is 0.37 to 0.45 pounds per foot.

The IC200CHS002 bracket is supplied with a label that can be inserted into the module’s clear door.

The IC8CHS2 carrier can accommodate current levels of 200 amps per power and ground connection or 002 amps per point.

The module will not be damaged by voltage transients up to 300 volts AC.The IC200CHS002 carrier supports up to 4 power/common connections and 32 I/O points.

The module features carrier-to-carrier mating connectors for quick installation of backplane connections. Keyed dials are also available with keys set to match the keying on the bottom of the module.

The IC200ALG230 is a VersaMax analogue input module. Formerly manufactured by GE Fanuc Automation, the module is now part of Emerson Automation.

This analogue input module has four (4) analogue inputs that can be configured specifically for voltage or current signals.

These are 4-20 mA current input signals and -10VDC / +10 VDC voltage input signals with 12-bit channel resolution.

About the IC200ALG230

The IC200ALG230 is an analogue input module from the Versamax modular I/O and control platform.

It is a compact analogue input module with four (4) individually configurable analogue input channels for voltage or current.

The module supports the interfacing of analogue signals, in particular unipolar 0 to 10VDC and bipolar +/-10 VDC voltage signals, as well as 4-20 mA current signals.

The IC200ALG230 is equipped with two (2) status LEDs for local reporting of the module’s operational status.

Specifically, the INT Power LED indicates www.abb-drive.com that internally generated field power is being supplied and the OK LED indicates that backplane power is actively supplied to the module.

The analogue input module has two (2) jumpers for setting the module’s mode of operation, either voltage or current and unipolarity for bipolar data.

The IC200ALG230 has a built-in analogue-to-digital converter with a resolution of 4?A = 8 counts (configured for current operation) and 2.5 mV = 8 counts (for voltage configuration).

The module has a typical response time of 0.4 ms and a filter response of 5.0 ms.

The module’s input data can be configured to hold to a *later state or to go to a defined value if a module error is detected.

The IC200ALG230 can be fitted with an auxiliary I/O terminal for signal wiring.

The terminal part number is IC200TBM001. 002 or 005.

Additionally, the terminal I/O bracket is available with catalogue number IC200CHS001. 002 or 005.

In addition, the terminal I/O bays can be used with compact terminal I/O bays catalogue number IC200CHS001. 002. or 005. catalogue number IC200CHS022. 025. and connector I/O bays part number IC200CHS003.

The GE Fanuc IC200ALG230 module is part of the Versamax product line.

It is an analogue input module compatible with 4 current inputs or 4 voltage inputs.

The IC200ALG230 analogue input module does not require an external power supply because it draws power from the power supply on the Versamax PLC backplane.

It is designed to interface with a Versamax PLC or Programmable Logic Controller system in a commercial or industrial environment.

All 4 of its inputs are single-ended and they are arranged in groups of 1. The IC200ALG230 Analogue Input Module draws 5 mA of backplane current at 125 V output voltage.

By default, its input voltage is +/- 10 volts DC bipolar, but it can be configured to have 0 to 10 volts unipolar.

Configuration of the GE Fanuc Versamax IC200ALG230 Analogue Input Module can be accomplished using 2 jumpers on the carrier terminals.

These jumpers can be used to configure the module to operate in current or voltage mode, and to configure the module to operate in unipolar or bipolar mode in voltage mode (if voltage mode is selected).

The jumper on the IC200ALG230 analogue input module for selecting current or voltage mode allows the module to accept input currents from 4 to 20 mA.

For safety, the cable of the IC200ALG230 analogue input module should be grounded at the source device whenever possible, and when it is not possible to ground the cable.

At a minimum, the cable shield should be grounded at the source device, or even at the I/O module.