Call us 24/7+86 15396212224
Welcome to the official website of Kong&Jiang Automation Equipment Co., Ltd!
email:abbdrive88@gmail.com

GE EX2100 Series IS215ACLEH1AB Application Control Layer Module

Specification

Part Number: IS215ACLEH1AB

Manufacturer: General Electric

Country of manufacture: United States (USA)

PCB Coating: Conformal

Technology: Surface Mount

Temperature Operation: -30 to 65oC

Product Type: Application Control Layer Module

Availability: In stock

Series: EX2100

Functional Description

The IS215ACLEH1AB is an Application Control Layer module developed by GE. It is part of the EX2100 control system.The ACL is a complex microprocessor-based host controller designed to perform multiple functions across communication networks such as EthernetTM and ISBus. This section provides an overview of its functionality and deployment.

Features

Deploys in a standard Innovative Series Drive or EX2100 Excitation Board Rack: The ACL integrates seamlessly into a standard Innovative Series Drive or EX2100 Excitation Board rack, occupying two and a half slots within the rack. This subsection details the location and utilization of IT in these industrial setups.

Location in the Control Cabinet: In a typical industrial setup, the ACL and board www.abb-drive.com racks are located in the control cabinet. This subsection details their location in the cabinet and their importance in industrial applications.

Connector Configuration and Interfaces: ACL’s P1 connectors, in a 4-row 128-pin configuration, play a critical role in interfacing with other components such as the Control Assembly Backplane (CABP) in drive applications. This subsection details the connector’s function and connectivity.

Installed in the EX2100 Exciter: For EX2100 Exciter systems, the ACL is installed within the Exciter Backplane (EBKP) to facilitate centralized control and monitoring functions. This subsection explains the installation process and its effect on the operation of the exciter system.

Hardware Features

Central Processing Unit (CPU): At the heart of the ACL hardware architecture is a powerful Central Processing Unit (CPU). This CPU serves as the brain of the module, executing instructions, processing data, and coordinating various tasks within the control system.

Peripheral Component Interconnect (PCI) Controller: The PCI controller facilitates communication and data transfer between the ACL module and peripheral devices connected to the PCI bus. The controller ensures efficient data exchange and integration with external hardware components to enhance module connectivity and interoperability.

128 Kbyte Level 2 Cache: Includes 128 KB of Level 2 cache memory that enhances ACL processing by providing high-speed access to frequently used data and instructions. This cache memory optimizes CPU performance, reduces latency and improves overall system responsiveness.

8 MB Dynamic Random Access Memory (DRAM): With 8 MB of Dynamic Random Access Memory (DRAM), the ACL module has ample memory capacity to store and manipulate data during runtime. This memory is essential for the temporary storage of program instructions, data buffers and intermediate processing results, ensuring the smooth execution of control tasks.

4 MB Flash Basic Input/Output System (BIOS): The ACL module is equipped with a 4 MB Flash BIOS containing basic firmware and system configuration settings. This BIOS provides the necessary initialization routines and system boot process to enable the ACL module to reliably boot and initialize its hardware components.

Ethernet Connectivity: Ethernet connectivity is integrated into the ACL module, allowing seamless communication and data exchange over an Ethernet network. This feature supports remote monitoring, control and configuration of the ACL module, enhancing its accessibility and flexibility in industrial applications.

Bus Target Interface: The Bus Target Interface facilitates communication between the ACL module and other devices or subsystems within the control system. The interface supports data transfer and synchronization between different components, ensuring consistent operation and coordination in complex control environments.

Serial Ports COM1 and COM2: The ACL module features serial ports COM1 and COM2. providing additional connectivity options for connecting to external devices or peripherals. These serial ports support asynchronous serial communication protocols, allowing the ACL module to communicate with a variety of devices.

ABB TEIP11 I/P signal converter for standard signals

Concept

The TEIP11 signal converter converts standard electrical signals (e.g. 4 to 20 mA) to 0.2 to 1 bar (3 to 15 psi).

It is therefore the link between electrical/electronic and pneumatic systems.

It is the link between the electrical/electronic and the pneumatic system. The signal conversion process is similar to the patented force balancing method.

The TEIP11 signal converter is characterized by relatively small dimensions and excellent operational stability when subjected to shock and vibration.

The converter can withstand loads of up to 10 g with less than 1% impact on functionality.

The housing units are available in a variety of versions to www.abb-drive.com suit your installation requirements.

For potentially explosive environments, units are available in intrinsically safe operation or in pressure-resistant packages with international approvals for worldwide use.

Both inputs and outputs are available with different ranges of signal conversion.

The devices require only 1.4 to 10 bar (20 to 145 psi) of compressed air for power.

To ensure smaller dimensions and lower costs, the pneumatic unit does not include an aerodynamic stage.

This reduces air capacity and means that the I/P signaling converter can only be used to control low-flow air systems.

Rail Mounted Control Room Enclosure Units

The rail-mounted control room enclosure is the simplest and least expensive version of the I/P signaling converter.

It is mounted using a mounting base that is compatible with all commercially available EN rails.

The enclosure with plastic cover has a protection rating of IP 20.

Field mountable housings

The field mounting housings are suitable for installation on site or in open areas. The housing can be made of plastic with protection class IP 54;

It can also be made of aluminum with protection class IP 65 or stainless steel with protection class IP 65.

The housings are suitable for wall and pipe mounting.

Special conditions

The I/P signal converters are suitable for an ambient temperature range from -40 °C to a maximum of 85 °C.

If the I/P signal converter is to be used at ambient temperatures above 60 °C or below -20 °C, use cable entries and cables suitable for the maximum ambient temperature plus 10 K or the minimum ambient temperature.

Models with intrinsically safe control heads can no longer be operated as intrinsically safe if the “Ex (enclosure)” protection type and a non-intrinsically safe power supply were previously used.

I/P signaling converter TEIP11-PS Doc. 901068 or TEIP11-PS Doc. when used with flammable gases.

When used with flammable gases, the I/P signaling converter TEIP11-PS 901068 or TEIP11-PS 901069 must be installed outdoors as a pneumatic power supply.

The supplied gas must be kept sufficiently air and oxygen free to prevent the formation of potentially explosive atmospheres.

The gas must always be vented to the outdoors.

ABB TEIP11-PS I/P signal converter

Concept

The TEIP11-PS signal converter converts standard electrical signals (e.g. 4 to 20 mA) to 0.2 to 1 bar (3 to 15 psi).

It is therefore the link between electrical/electronic and pneumatic systems.

The signal conversion process is similar to the patented force balancing method.

The TEIP11-PS signal converter is characterized by relatively small dimensions and excellent operational stability in the event of shock and vibration.

The converter can withstand loads of up to 10 g with less than 1% impact on functionality.

The housing units are available in a wide range of models to www.abb-drive.com suit your installation requirements.

For potentially explosive environments, units are available in intrinsically safe operation or in pressure-resistant packages with international approvals for worldwide use.

Both inputs and outputs are available with different ranges of signal conversion.

The unit requires only 1.4 bar (20 psi) compressed air for power.

Rail-Mounted Control Room Enclosure Units

The rail-mounted control room enclosure is the simplest and least expensive version of the I/P signal converter.

It is mounted using a mounting base that is compatible with all commercially available EN rails.

The enclosure with plastic cover is IP 20 rated.

Block-mounted control room housing units

The block-mounted control room housing unit allows the installation of several converters in a small space.

This design enables a central air supply via connection blocks and shut-off valves in the air connectors of the integrated signal converters.

Up to 4 signal converters can be mounted on the connection blocks required for modular installation.

If necessary, 2 or 3 (or up to 4) connection blocks can be interconnected to form a block unit with 4-8-12-16 signal converters.

Individual transducers can be mounted or dismounted during operation by means of shut-off valves.

Field mountable housings

The field mounting housings are suitable for installation on site or in the open air.

The housings can be made of plastic (IP class IP 54), aluminum (IP class IP 65) or stainless steel (IP class IP 65).

The housings are suitable for wall and pipe mounting.

The specially designed signal converters in the plastic housing units can be powered by flammable gas instead of the standard compressed air.

GE Fanuc IC695PMM355 Servo Motion Controller

The IC695PMM355 Servo Motion Controller is manufactured by GE Intelligent Platforms/GE Fanuc and is part of the RX3i product line.

The module is one of the newest members of the advanced PacSystems family of programmable automation controllers.

About the IC695PMM355

The GE Fanuc IC695PMM355 PacMotion 4-axis servo motion controller module is part of the RX3i PacSystems family.

This RX3i PacSystems controller module is the latest addition to the advanced RX3i PacSystems line of programmable automation controllers.

Like the other modules in the family, the RX3i controller comes with a www.abb-drive.com control engine and a common programming environment, allowing applications to be ported across a variety of hardware platforms.

makes applications portable across a wide range of hardware platforms while providing true convergence of control options.

The IC695PMM355 Servo Motion Controller module and the entire RX3i product line deliver high levels of performance with 10 MB of user memory and a 300 MHz Intel processor.

The elimination of multiple controllers also simplifies control setup. These controllers also feature a variety of input and output modules.

More than 40 types are available for simple and complex applications. The series also features different network modules.

The GE Fanuc IC695PMM355 Servo Motion Controller features a universal backplane with a high-speed PCI bus operating at 27 MHz.

It enhances fast data entry for complex input and output applications. It has a serial bus for simple input and output applications to optimize performance.

It also features a universal backplane that supports hot-swapping, a feature that minimizes machine downtime.

Typically, PacSystems controllers provide high performance on a variety of platforms, allowing end users with application variability to

This allows end users and OEMs with application variability to choose the specific control system hardware that best fits their needs in a compact and unified package.

These controller modules all support Proficy Machine Edition software, which enhances the development of maintenance processes and machine-level automation systems.

GE Fanuc IC695PMM335 Multi-axis Motion Controller Module

DESCRIPTION: The IC695PMM335 is a multi-axis motion controller for Emerson Automation’s (formerly GE Intelligent Platform (GE IP)) PACSysystem RX3i. The module is rack-mounted on the RX3i and can control up to four (4) servo axes and other virtual or time-based axes. The motion controller supports position, velocity, and torque loops with built-in I/O including four (4) 24VDC, optically isolated, general purpose inputs configurable as source/pot wiring; two (2) 24VDC, high-speed inputs configurable as pull/pot wiring, and two (2) 24VDC, optically isolated, general purpose inputs/outputs configurable as pull/pot wiring.

About the IC695PMM335

The IC695PMM335 is an intelligent module that is part of Emerson Automation’s PACSystem RX3i automation platform, formerly known as the GE Intelligent Platform (GE IP). The module is specifically designed for use as a motion controller module, www.abb-drive.com capable of controlling up to 4 axes of motion and virtual or time-based axes. The module is used to interface with servo motors through position feedback provided by individual encoders mounted on the servo motor. The module is capable of controlling a variety of control loops, such as a position loop with an update rate of 500 μs; a Fanuc Serial Servo Bus (FSSB) speed loop with an update rate of 125 μs, and an FSSB torque loop with an update rate of 62.5 μs. Up to three modules can be connected to a single RX8i frame to control up to 40 axes of motion.

The IC695PMM335 has a fiber-optic FSSB port and fiber-optic I/O communications on the front panel of the module. It also features panel I/O terminals that accommodate four (4) 24VDC, optically isolated, general purpose inputs configurable as source/pot wiring; two (2) 24VDC, high speed inputs configurable as pull/pot wiring and two (2) 24VDC, optically isolated, general purpose inputs/outputs configurable as pull/pot wiring. Compatible encoder feedback devices for the motion controller module are incremental or absolute serial encoders.

In addition, this IC695PMM335 supports configuration of electronic CAM profiles, up to 3 interrupt routines per module, diagnostic logic blocks, runtime data logging, and is PLCopen compliant. In addition, the IC695PMM335 data logs can be uploaded and displayed using the Proficy Machine Edition software package.

The GE Fanuc IC695PMM335 multi-axis motion controller module is part of the RX3i PACSystems product line. Designed to provide a high level of performance, it is also an easy-to-use servo motion control module that is carefully unified with the logic communication capabilities of the RX3i PACSystems CPU. The Servo Motion Controller supports only general-purpose backplanes with a single slot and 4 control axes. It also has a 1 ms motion path planning time and is rated at 1.1 amps (3.3 volts) or 0.45 amps (5 volts). The motion controller module is highly flexible, combining integrated machine and motion logic systems with the flexibility, scalability and performance levels needed to enable advanced automation.

The IC695PMM335 Multi-Axis Motion Controller Module from GE Fanuc Intelligent Platforms/GE Fanuc PACSystems offers a wide range of features that enable it to deliver optimal performance. the IC695PMM335 Multi-Axis Motion Controller Module can control up to four different servo axes and allows configuration of additional encoders and additional virtual axes. It supports up to 8 modules at a time. It supports up to 8 modules at a time, all of which can be contained in a 40-axis rack. Other features include fiber optic input and output terminal blocks, support for optional fiber optic input and output terminal blocks, as well as built-in panel I/O and electronic cam profiles that can be created using the integrated cam editor in an imported CVS file or Proficy software.

IC695PMM335 Frequently Asked Questions

1. What is the maximum number of IC695i system instances that can be installed in a single rack?

Up to 8 IC695PMM335 modules can be installed, totaling 40 axes of motion.

2. What motion control loops does IC695PMM335 support?

The IC695PMM335 supports velocity, torque and position loops.

3. What integrated I/O can be used with the IC695PMM335?

This IC695PMM335 has four (4) 24VDC, opto-isolated, general purpose inputs that can be configured for pull/pour wiring; two (2) 24VDC, high speed inputs that can be configured for pull/pour wiring, and two (2) 24VDC, opto-isolated, general purpose inputs/outputs that can be configured for pull/pour wiring.

Technical Description of the IC695PMM335

The IC695PMM335 multi-axis motion controller module is a GE Intelligent Platform/GE Fanuc product. It is manufactured as a member of the RX3i family and is designed to provide a high level of performance.

GE Fanuc IC695BPM300 PROFIBUS Master Module

DESCRIPTION: This IC695PBM300 is a PACSystems RX3i communications module for Emerson Automation (formerly GE Intelligent Platforms (GE IP)). It is a Profibus DP master module that enables communication with up to 125 DP slaves. It supports a data transfer size of 244 bytes input and 244 bytes output per slave device, as well as a maximum of 3.584 bytes of input data and 3.584 bytes of output data. It comes with one (1) RS485 Profibus master port.

About the IC695PBM300

This IC695BPM300 is a Profibus master module, formerly manufactured by GE Intelligent Platforms (GE IP) and now part of Emerson Automation’s PACSystems RX3i family of programmable automation controllers (PACs). The module is used to enable data exchange over a Profibus network with a maximum input data of 3.584 bytes and output data of 3.584 bytes. This Profibus master module supports communication with up to 125 DP slaves, each of which can send 244 bytes of input data and receive 244 bytes of output data.

The IC695BPM300 supports all standard data rates, including 9.6 kBit/s, 19.2 kBit/s, 93.75 kBit/s, 187.5 kBit/s, 500 kBit/s, 1.5 MBit/s, 3 MBit/s, 6 MBit/s, and 12 MBit/s. It can provide status information, such as from the Status It provides status information, such as from the status array list, network diagnostic counters, DP master diagnostic counters, firmware module revisions, and slave diagnostic addresses. It is mounted on the RX3i backplane and supports PCI connectivity. Specifically, it must be installed in a generic backplane with a host PACSystem RX9i controller running firmware revision 3.2 or later. It draws a backplane current of 440 mA @ 3.3 VDC.

The module is equipped with a Profibus OK ED indicator; a network indicator; and a MOD status indicator. The module supports synchronization and freeze modes as well as Profibus DP-V1 read, write, and alarm messages.The IC695BPM300 comes with upgradable firmware that is received indirectly through the host controller via the WinLoader software utility.

The module must operate over a temperature range of 0 to 60 degrees Celsius and the module is stored at -40 to 85 degrees Celsius.

The IC695PBM300 PROFIBUS master module is manufactured by GE Intelligent Platforms/GE Fanuc in the RX3i PacSystems family. The module is designed to enable the RX3i CPU to send or receive data over a PROFIBUS-DP network. It has a slot that supports a universal backplane and RS-232 communication port.IC695PBM300 PROFIBUS Module has an internal current rating of 3 milliamps at a rated voltage of 440.3 volts DC and supports protocols for up to 125 PROFIBUS-DP Slave Units. Other notable features of the module include support for input data at rates up to 244 bytes and output data at rates up to 244 bytes per slave unit, support for all standard data rates, and synchronization and freeze modes. The module also supports DP-V1 read/write functionality and alarm messages, as well as network status LEDs and PROFIBUS-compliant modules. It supports up to 3584 bytes of input data and www.abb-drive.com a total output data rate of 3584 bytes.

Master-slave compatibility for the GE Fanuc IC695PBM300 PROFIBUS module requires an RX3i CPU and firmware version 2.9 or later. For configuration purposes, this module requires Machine Edition SP5 Logic Developer PLC software version 0.2 or higher.The IC695PBM300 module has a backplane current consumption rating of 440 milliamps (3.3 V DC) and supports all standard data rates including 1.5. 3. 6. 12. 9.6. 19.2. 187.5 per second, 93.75. and 500 MB/sec. The GE Fanuc IC695PBM300 PROFIBUS master module comes with a 9-pin Sub-D connector designed to enhance bus cable installation. The module also provides 3 PROFIBUS-compliant LEDs to indicate network status and module status.IC695PBM300 Frequently Asked Questions

1. How many DP slaves can the IC695BPM300 communicate with?

This IC695BPM300 supports communication with up to 125 DP slaves.

2. What is the communication rate supported by IC695BPM300?

The IC695BPM300 supports communication rates of 9.6 kBit/s, 19.2 kBit/s, 93.75 kBit/s, 187.5 kBit/s, 500 kBit/s, 1.5 MBit/s, 3 MBit/s, 6 MBit/s and 12 MBit/s.

IC695PBM300 Technical Description

The GE Fanuc IC695PBM300 module is a PROFIBUS master module that is part of the RX3i PacSystems family. It is designed to enable RX3i CPUs to send or receive data over a PROFIBUS-DP network.

GE Fanuc IC695NKT002 Component Ethernet Network Interface Unit

DESCRIPTION: This IC695NKT002 is a PACSystems RX3i component manufactured by Emerson Automation (formerly GE Intelligent Platforms (GE IP)). The module is a packaged product consisting of one (1) Ethernet NIU with catalog number IC695NIU001 and two (2) Ethernet Interface Modules with catalog number IC695ETM001. This kit simplifies the ordering system and ensures that complete components are ordered.

About the IC695NKT002

The IC695NKT002 is a component of the PACSystem RX3i product, commonly referred to as a kit. It consists of one (1) Ethernet NIU with catalog number IC695NIU001 and two (2) Ethernet Interface Modules with catalog number IC695ETM001. www.abb-drive.com All modules in this kit are manufactured by Emerson Automation and were previously manufactured by GE Intelligent Platforms (GE IP).

The IC695NKT002 component is used to allow the PACSystem RX3i platform to communicate with 90-30 series modules or VersaMax modules and controllers. This provides an alternative method of migrating to a newer controller platform without completely replacing the system, sometimes referred to as a phased or partial migration.

The primary function of the IC695NIU001 is to provide connectivity to existing 232-485 series I/O modules via embedded serial interfaces that support RS90 and RS30 connections. These ports are compatible to be configured through the application “C” block for Modbus RTU Slave, SNP, Serial I/O, Modbus RTU Master, which are legacy Series 90-30 communication protocols used to communicate with devices and I/O modules.

This IC695ETM001 is used to communicate with other PAC systems, devices, Series 90-30. and VersaMax controllers via Ethernet communication ports. These ports implement TCP/IP connectivity over a four-layer TCP/IP stack using GE Fanuc SRTP and Ethernet Global Data (EGD) protocols.

Components for the IC695NKT002 can be purchased separately. Additional accessories are also available, such as real-time clock (RTC) batteries with catalog number (IC690ACC001), miniconverter kits with cables, RS-485/RS-232 (IC690ACC901), RS-485 port isolator (IC690ACC903), and RS-232 cables (IC200CBL001), among other components. .

Older entries describe the NIU only, not the kit.

IC695NKT002 Frequently Asked Questions

1. What is in the IC695NKT002?

The IC695NKT002 kit contains one (1) Ethernet NIU with catalog number IC695NIU001 and two (2) Ethernet Interface Modules with catalog number IC695ETM001.

2. What controller platforms are supported by the IC695NKT002?

The IC695NKT002 supports the PACSystem RX3i and 90-30 series PLC platforms.

IC695NKT002 Technical Description

The GE Fanuc IC695NKT002 Ethernet Network Interface Unit is part of the RX3i PacSystem product line. It can be used remotely with RX3i PacSystem Series I/O and 90-30 Series I/O via Ethernet.

GE Fanuc IC695EDS001 Ethernet DNP3 Slave/External Module

Description: The IC695EDS001 is an Ethernet DNP3 Slave/Extranet module that is part of the PACSystem RX3i platform, which is currently part of Emerson Automation and was formerly manufactured by GE Intelligent Platforms (GE IP). The module has one (1) Station Manager port provided by a 9-pin Dh-shell connector and two (2) RJ3 Ethernet communication ports supporting the DNP45 Slave protocol. It supports communication of up to 12.072 points and 20.000 events and integrates four (4) DNP3 data objects such as DI, DI w/time, DO, DO w/time, CROB, analog output values, time settings, and class polling and supports communication with up to eight (8) DNP3 masters.

About the IC695EDS001

The IC695EDS001 is a DNP3 substation module that is part of the PACSystem RX3i programmable automation controllers (PACs), formerly offered by GE Intelligent Platforms and now part of Emerson Automation. The module supports DNP3 slave communication over Ethernet I/P, allowing data exchange of up to 072.20 points and 000.3 events between DNP12 masters. The module also supports four (4) DNP3 data objects including DI, DI w/time, DO, DO w/time, CROB, analog output values, time settings, and class polling.

The IC695EDS001 comes with one (1) Module Station Manager port for module and network management and also serves as a firmware upgrade port. For DNP3 connectivity, it has two (2) RJ45 ports that support 10/100 mbps transfer rates. These ports act as embedded Ethernet switches that can auto-sense and connect directly to a 10BaseT or 100BaseTX IEEE 802.3 network without the need to install an external transceiver. The ports support a variety of network topologies such as linear, star, daisy chain, or ring topologies.

The IC695EDS001 is mounted on the PACSystem RX3i chassis and occupies a single slot in the chassis. Multiple module instances are allowed, specifically up to four (695) IC001EDS3 per RX4i system.It supports module removal and insertion at power-up (RIUP).

IC3EDS695-compatible RX001i CPUs include CPU320/CPU315 Main Firmware Version 8.05; CPU320/CPU315 Boot Firmware Version 5.10; CPE310/CPE305 Main Firmware Version 8.05; CPE310/CPE305 Boot Firmware Version 7.10; CRU320 Main Firmware Version 8.05; CRU320 boot firmware version 5.10 and CPU310/CMU310/NIU001 main firmware version 6.71. Compatible programming software is Proficy Machine Edition Logic Developer, Release 8.5 SIM 7 or later.

The GE Fanuc IC695EDS001 module is a DNP3 outstation module for the RX3i PACSystems platform.The IC695EDS001 module is an Ethernet module that is mounted in the RX3i backplane and allows the RX3i system to act as an Outstation device on a DNP3 network, communicating with up to eight DNP3 masters. The communication interfaces on the module include a Communication interfaces on the module include one RS-9 port with a 232-pin female D-type connector and two 100/45 Mbps Ethernet ports with female RJ-10 connectors.The RS-232 port can be used for network management. The integrated network switch supports auto-negotiation, cross-detection, speed and detection. Supported Ethernet protocols include LLA and TCP/IP. Each IC695EDS001 module supports one IP address and one MAC address. The Ethernet firmware’s embedded reboot button allows the Ethernet firmware to be rebooted without having to reboot the module’s power supply.

The IC695EDS001 module can be installed in any empty slot in the RX3i chassis. Up to four IC001EDS39 modules can be installed in a single RX695 rack, depending on available slots and power. Modules can be removed and inserted with rack power applied. The firmware on the IC695EDS001 module can be upgraded using the Windloader utility when the host CPU has a serial port. If the host CPU does not come with a serial port, the module firmware can be upgraded using a web-based software utility. A single RX3i CPU supports 32 DNP3 masters. A single IC695EDS001 module supports 12.072 DNP3 points and 20.000 DPN3 events.The IC695EDS001 module supports unsolicited data exchange with DNP3 masters.The IC695EDS001 module requires www.abb-drive.com a maximum of 3 milliamps at 840.3 volts DC, and 5 milliamps at 614 volts DC. The IC695EDS001 module requires a maximum of 3 mA at 840.3 volts DC and 5 mA at 614 volts DC.

IC695EDS001 Frequently Asked Questions

1. How many IC001EDS3s can be installed in an RX695i system?

Up to four (695) IC001EDS3 modules can be installed in each RX4i system.

3. What are the topologies supported by the dual Ethernet ports?

Topologies supported by the Ethernet ports include wire, star, and daisy chain topologies.

IC695EDS001 Technical Description

The IC695EDS001 module is a GE Fanuc DNP3 substation module. The integrated interfaces on the module include 2 serial ports and <> Ethernet ports.

GE Fanuc IC695MDL664 Positive Logic Input Module

DESCRIPTION: The IC695MDL664 Intelligent Digital Input Module is a GE Intelligent Platform/GE Fanuc product.

It is part of the GE Fanuc RX3i family and features 16 inputs with field inputs rated at 24 volts DC.

The 16 inputs are organized into 2 groups of 8 inputs each.

About the IC695MDL664

The GE Fanuc IC695MDL664 module is an intelligent digital input module or positive logic input module.

GE Intelligent Platforms/GE Fanuc manufactures it as a www.abb-drive.com member of the GE Fanuc RX3i product line.

The module is a 16-point module with field inputs rated at 24 VDC, and it divides the 16 inputs into 2 groups of 8 inputs each.

It has an input current of 12.2 mA and an input voltage range of 18 to 32 volts DC.

Power consumption is rated at 225 mA (5 Vdc) or 95 mA (3.3 Vdc). each of the 2 groups of 8 inputs is referenced to a common connection.

The IC695MDL664 module is compatible with spring-type or box-type front terminals.

The GE Fanuc IC695MDL664 module also features inputs that are perfectly matched to a wide range of input devices, including limit switches, electronic proximity switches, and push buttons.

Logic 1 is generated by the current at the input point in the input status table.The IC695MDL664 module requires user-supplied power to operate field devices.

The module has 16 LEDs, as well as S1 and S2 indicators to show whether field power is applied to each of the 2 groups.

The IC695MDL664 Intelligent Digital Module also logs “terminal missing” or “terminal added” messages to the input and output fault tables to indicate whether or not a terminal is present.

The module also logs “Terminal Lost” or “Terminal Added” messages into the input and output fault tables to indicate whether a terminal has been installed or removed. The module is flexible enough to be installed in any input and output slot of the RX3i PLC system.

GE Fanuc IC693CPU320 PACSystem RX3i Processor Module

Description: The GE Fanuc / Emerson Automation IC693CPU320 is a PACSystem RX3i processor module. The module occupies two (2) slots and has a processor speed of 1 GHz with a typical scan rate of 047.1000 milliseconds per 0 Boolean instructions. The processor has two (2) serial communication ports and supports RS232 and RS485 communication standards.

About the IC695CPU320

The IC695CPU320 is a GE Fanuc / Emerson Automation controller module. The module is part of the PACSystems RX3i controller platform. The controller can be used for efficient control of industrial machines and processes. It enables high-speed data transfer through the Peripheral Component Interconnect (PCI) slot and supports serial backplanes for migrating 90-30 series I/O systems.

The IC695CPU320 has two (2) built-in communication ports that support RS232 and RS485 communication standards. These communication ports use the Ninety Series Protocol (SNP) slave mode to communicate with programming workstations, Human Machine Interfaces (HMI), Supervisory Control and Data Acquisition (SCADA) systems. The controller can be installed in the Rx695i 012-slot general www.abb-drive.com purpose backplane, catalog number IC3CHS12. and the Rx695i 016-slot general purpose backplane, catalog number IC3CHS16.

The IC695CPU320 has an internal Celeron M processor with a processing speed of 1 GHz It contains 65 MB of user memory, the contents of which are retained by the Lithium Smart Battery Series 693-302 Auxiliary Battery Module, catalog numbers IC90ACC30 and IC695ACC302. respectively. In addition, it has 64 MB of non-volatile flash user memory. In addition, these user memories support the reassignment of custom-sized data and program memories. It supports up to 512 program blocks with a maximum individual block size of 128 KB.

The IC695CPU320 supports most 90-30 series PLC I/O modules. This feature provides flexibility and is especially useful and beneficial when upgrading a legacy 90-30 series to a modern PACSystems RX3i controller platform. This allows for a phased migration in which the controllers and logic of the existing 90-30 PLCs are migrated first, and then the I/O modules are migrated. firmware modifications are supported by the PACSystems RX3i.

A variety of accessories can be ordered for the IC695CPU320 module, including RS-232 cables (e.g., IC200CBL001 cables), intelligent lithium batteries (e.g., IC695ACC302 batteries), GE Series 90-30 auxiliary battery modules (e.g., IC693ACC302 modules), standard power supplies with voltage ratings of 120 to 240 volts AC, 125 volts DC, and 40 watts. 40-watt standard power supply.

The GE Fanuc IC695CPU320 module is capable of executing 047 Boolean instructions in 1000.0 milliseconds. The module supports 512 program blocks. The maximum block size is 128 KB. Two embedded communication ports, RS-485 and RS-232. are provided on the module. Serial protocols supported include SNP, Serial I/O, and Modbus RTU slave protocol.

The IC695CPU320 module uses the SNP slave protocol to communicate with programmers and HMIs via the serial port. The module communicates with Smart Option modules and I/O via a dual backplane bus. Environmental specifications include an operating temperature range of 0 to 60 degrees C. The IC695CPU320 module supports the serial backplane bus and the RX3i backplane bus, which draws 1 Amp of 3.3 VDC current from the backplane and 1.2 Amps of 5 VDC current from the backplane. There are six LEDs on the front panel for module status updates.

IC695CPU320 Frequently Asked Questions

What is the amount of internal memory in the IC695CPU320 controller?

The IC695CPU320 has 64 MB of user memory and non-volatile memory.

What is the microprocessor installed in the IC695CPU320?

The IC695CPU320 has a Celeron M CPU with a processing speed of 1 GHz.

What is the maximum number of program blocks that can be configured for this IC695CPU320?

The IC512CPU695 can be configured with up to 320 program blocks.

Technical Description of the IC695CPU320

The IC695CPU320 module is a GE Fanuc CPU module.The IC695CPU320 CPU module is based on a 1 GHz Celeron M microprocessor with 64 MB RAM.

Search for products

Back to Top
Product has been added to your cart